Skip to content
Omnikalc

Conduit offset bend calculator: multiplier, marks and shrink

Enter the height of the offset, the angle of the bends, the first mark and the required run to get the multiplier, the distance between the marks, the shrink and the length of conduit to cut.

Updated on
Your inputs
in

Value out of range

in

Value out of range

in

Value out of range

Results

Distance between the two marks

12.0 in

Multiplier of the offset
2.00
Shrink of the offset
1.61 in
Position of the second mark
42.0 in
Length of conduit to cut
121.61 in

The conduit offset bend calculator gives the multiplier, the distance between the two marks, the shrink, the position of the second mark and the length of conduit to cut for an offset bend of an EMT or a rigid conduit, from the height of the offset and the angle of the bends.

How the calculation works

  • Enter the height of the offset, that is the distance to move the conduit, and choose the angle of the bends.
  • Enter the distance from the end of the conduit to the first mark and the length of the straight run you need.
  • The calculator finds the multiplier, the distance between the marks, the shrink, the second mark and the length to cut.

Example

To move a conduit by 6 in with 30 degree bends, the multiplier is 1 / sin 30° = 2.00, so the marks are 12.0 in apart. The first mark is at 30 in from the end, so the second one is at 42.0 in. The offset shortens the conduit by 6 × (1 − cos 30°) / sin 30° = 1.61 in, so a straight run of 120 in needs a conduit of 121.61 in.

Why it matters

The calculator helps electricians, apprentices, instructors and students to mark an offset quickly, to check the multiplier and the shrink of the usual angles, and to cut the conduit to the right length before the bending on the site.

Good to know

Mark the conduit on the flat side and use the same direction of the bender for both bends. Keep the conduit in the same plane while you bend it, and rotate it by exactly half a turn for the second bend. Make a test offset on a scrap of conduit, and check the height with a tape before you fix the conduit.

The conduit fill calculator checks the number of conductors in a conduit, the cable tray fill calculator checks a cable tray, the wire size calculator gives the size of a conductor and the rolling offset calculator gives the length of a pipe offset in two planes.

Frequently asked questions

What is an offset in a conduit?

An offset is a pair of equal bends, made in opposite directions, that moves the conduit in a new line parallel to the old one. Electricians use it to go over a box, a pipe or a beam, or to enter a panel in line with the knockout. The two bends are made at the same angle, and the straight part between them is the travel of the offset.

What is the multiplier?

The multiplier is the number by which the height of the offset is multiplied to get the distance between the two marks on the conduit. It is the cosecant of the angle of the bends, that is 1 divided by the sine. For 30 degrees it is 2.0, for 45 degrees it is 1.414, for 22.5 degrees it is 2.613, and for 10 degrees it is 5.76. A small angle gives a long and gentle offset.

What is the shrink?

The shrink is the length which the offset takes from the conduit, because the conduit follows a longer path along the bends than along a straight line. It is the height of the offset times (1 − cos of the angle) divided by the sine of the angle. It is about 1/4 in per inch of offset at 30 degrees, and 3/8 in per inch at 45 degrees. The shrink must be added to the length of the conduit that you cut.

What are the limits of the calculator?

The calculator uses the geometry of an ideal offset. It does not take into account the radius of the bender, the spring back of the conduit, the gain of the bends or the error of the marks. The first bend must be made at the mark of the bender with the right orientation, and a test bend on a scrap of conduit is a good way to check the result before the real work.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.