Skip to content
Omnikalc

Milling feed rate calculator: feed, removal rate and spindle power

Enter the cutter, cutting speed, chip load, depth and width of cut to get the spindle speed, feed rate, material removal rate and the power the pass needs.

Updated on
Your inputs
in

Value out of range

Value out of range

SFM

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

hp

Value out of range

Results

Table feed rate

41.3 in/min

Spindle speed
4,584 rpm
Material removal rate
5.16 in³/min
Spindle power needed
1.55 hp
The cut is within your spindle power
Cutting time for the pass
17.5 s
Feed per revolution
0.0090 in

Milling is a balance of three things: how fast the cutter turns, how fast the table moves and how much metal each tooth takes. This calculator turns a cutting speed and a chip load into a spindle speed, a feed rate, a material removal rate and the spindle power the pass needs, then compares the power with what your machine can deliver. It also gives the time for a pass of a given length.

How the calculation works

  • Spindle speed (rpm) = cutting speed (SFM) × 12 ÷ (π × diameter)
  • Feed rate (in/min) = rpm × number of teeth × chip load per tooth
  • Material removal rate (in³/min) = radial width × axial depth × feed rate
  • Spindle power (hp) = removal rate × specific power of the material (0.3 aluminum, 1.0 mild steel, 1.4 stainless steel)
  • Cutting time = length of cut ÷ feed rate

Example

A ½ in, 3-flute end mill cuts aluminum at 600 SFM with a chip load of 0.003 in, 0.5 in deep and 0.25 in wide. The spindle runs at 4,584 rpm and the feed rate is 41.3 in/min. The removal rate is 5.16 in³/min, which needs 1.55 hp at the spindle, within a 3 hp limit. A 12 in pass takes 17.5 s.

Why it matters

Running a mill from a feeds-and-speeds sheet instead of by feel saves tools and finishes: too slow a feed rubs and work-hardens the material, and too fast a feed breaks the cutter. The removal rate shows how much a change in depth or width costs in power, and the time per pass lets you quote a job. On a small machine, power is often the limit rather than speed.

Good to know

Chip thinning when the radial width is under half the diameter lets you raise the feed per tooth. The specific power figures are rough averages for sharp tools and vary with the grade and the tool geometry. Deflection of long, thin cutters, rigidity of the setup and coolant also limit the cut. Always follow the tool maker’s data first. This tool is for education.

In practice

Start with the maker’s recommended chip load at about 70 % of the suggested speed, then raise the speed and feed in steps while listening to the cut. Keep the radial width at 10 to 40 % of the diameter for full-depth slots, and finish with a light pass at a higher speed.

The cutting speed calculator converts SFM into rpm for drilling, milling and turning, the horsepower and torque calculator relates power to speed, and the speed from rpm calculator works the other way.

Frequently asked questions

How do I calculate the feed rate for milling?

Multiply the spindle speed by the number of teeth and by the chip load per tooth: feed rate = RPM × flutes × chip load. The spindle speed itself comes from the cutting speed, RPM = SFM × 3.82 ÷ diameter.

What is the chip load?

It is the thickness of material each tooth cuts per revolution, in inches or millimetres per tooth. Too small a chip load rubs and heats the tool, and too large a one can break it. Tool makers publish a range for each material and cutter size.

What is the material removal rate?

It is the volume of metal removed per minute: width of cut × depth of cut × feed rate. It measures how productive a pass is, and it sets the power the spindle must supply.

Why does the calculator check spindle power?

Power is roughly the material removal rate times the specific power consumption of the material. Steel takes about three times as much power as aluminum for the same removal rate. If the needed power exceeds what the spindle gives at that speed, the cut will stall.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.