Skip to content
Omnikalc

Carbon equivalent calculator: will this steel crack when you weld it?

Enter the chemical composition of the steel to get the IIW carbon equivalent, the Pcm parameter and a weldability rating.

Updated on
Your inputs
%

Value out of range

%

Value out of range

%

Value out of range

%

Value out of range

%

Value out of range

%

Value out of range

%

Value out of range

%

Value out of range

%

Value out of range

Results

Carbon equivalent (IIW formula)

0.436

Moderate: preheat or low-hydrogen practice may be needed on thick sections
Pcm weld cracking parameter
0.2755
Share of the carbon equivalent from carbon
41.3 %
Share of the carbon equivalent from manganese
45.9 %

Some steels weld easily and others crack next to the weld unless you preheat them, and the difference lies mostly in the chemistry. The carbon equivalent calculator takes the percentages of carbon, manganese, silicon, chromium, molybdenum, vanadium, nickel, copper and boron and gives the IIW carbon equivalent, the Pcm parameter, the share due to carbon and the share due to manganese, with a weldability rating.

How the calculation works

  • Enter the percentages by weight of each element from the mill certificate: carbon, manganese, silicon, chromium, molybdenum, vanadium, nickel, copper and boron.
  • The IIW carbon equivalent is CE = C + Mn/6 + (Cr + Mo + V)/5 + (Ni + Cu)/15.
  • The Pcm parameter is C + Si/30 + (Mn + Cu + Cr)/20 + Ni/60 + Mo/15 + V/10 + 5B, used for low-carbon steels, where it is more accurate.
  • Read the rating: below 0.35 the steel is easy to weld, from 0.35 to 0.45 preheat may be needed on thick plate, and above 0.45 preheat and low-hydrogen practice are needed.

Example

A structural steel has 0.18 % C, 1.20 % Mn, 0.30 % Si, 0.10 % Cr, 0.05 % Mo, 0.03 % V, 0.10 % Ni, 0.20 % Cu and 0.0005 % B. The carbon equivalent is 0.18 + 0.20 + 0.036 + 0.020 = 0.436, which is moderate. The Pcm parameter is 0.2755. Carbon provides 41.3 % of the carbon equivalent and manganese 45.9 %.

Why it matters

A quick look at the mill certificate tells a welder whether a plate needs preheat, special electrodes or a slow cooling plan. Comparing the carbon equivalent of two grades also shows why a stronger steel is often harder to weld, and whether a change of supplier or heat number is safe for an existing procedure.

Good to know

The thresholds are rules of thumb for common structural steels and thicknesses up to about 1 inch (25 mm). Thick sections, high restraint, high hydrogen and low heat input all call for more caution, and special alloys, stainless steels and cast irons need their own methods. The mill certificate is the source of the chemistry. Treat the rating as a screening figure, not as a procedure.

The welding heat input calculator gives the energy per unit length of the weld, the Brinell hardness calculator relates hardness to strength, the metal weight calculator estimates the mass of plates and bars, and the bolt torque calculator sizes the tightening of fasteners.

Frequently asked questions

What is the carbon equivalent?

It is a single number that adds up the effect of the alloying elements on the hardenability of the steel, expressed as an equivalent amount of carbon. The higher it is, the more likely the heat-affected zone of a weld is to form hard, brittle martensite and to crack with hydrogen. Welding codes use it to decide on preheat.

What is the difference between the IIW formula and Pcm?

The International Institute of Welding formula suits steels with more than about 0.12 % carbon. The Pcm formula, from Ito and Bessyo, was developed for modern low-carbon, high-strength steels and includes silicon and boron. When the carbon is below 0.12 %, the Pcm is usually the better guide.

What carbon equivalent can be welded without preheat?

As a rule of thumb, steels below about 0.35 are easy to weld in normal thicknesses. Between 0.35 and 0.45, preheat depends on the thickness, the hydrogen level and the restraint. Above 0.45 you normally need preheat, low-hydrogen consumables and controlled cooling. Follow your welding procedure specification and the code.

Does the calculator give a preheat temperature?

No. The preheat depends on the carbon equivalent, the thickness, the heat input, the hydrogen level and the joint restraint. Codes such as AWS D1.1 and EN 1011 give methods to compute it. This calculator gives the composition index that feeds into them and a first rating of the weldability.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.