Skip to content
Omnikalc

Weld preheat temperature and carbon equivalent calculator

Enter the chemical composition of the steel and the thickness of the plate to get the carbon equivalent, the effect of the thickness and the preheat temperature for welding.

Updated on
Your inputs
%

Value out of range

%

Value out of range

%

Value out of range

%

Value out of range

%

Value out of range

%

Value out of range

%

Value out of range

in

Value out of range

Results

Preheat temperature

353 °F

Carbon equivalent of the steel
0.453
Preheat and low-hydrogen practice are advised
Added by the thickness
0.057
Carbon equivalent with the thickness
0.510

The weld preheat calculator gives the carbon equivalent of the steel, the part added by the thickness and the preheat temperature to avoid cold cracking, from the chemical composition of the steel and the thickness of the thickest plate to be welded.

How the calculation works

  • Enter the carbon, manganese, chromium, molybdenum, vanadium, nickel and copper content of the steel in percent.
  • Enter the thickness of the thickest plate to be welded.
  • The calculator finds the carbon equivalent, the part added by the thickness and the preheat temperature.

Example

A steel with 0.20 % C, 1.20 % Mn, 0.10 % Cr, 0.05 % Mo, 0.03 % V, 0.10 % Ni and 0.15 % Cu has a carbon equivalent of 0.20 + 1.20 / 6 + 0.18 / 5 + 0.25 / 15 = 0.453. For a plate 1 in (25.4 mm) thick, the thickness adds 0.005 × 25.4 × 0.453 = 0.057, for a total of 0.510. The preheat is 350 × √(0.510 − 0.25) = 178.5 °C, that is 353 °F.

Why it matters

The calculator helps welders, welding inspectors, fabricators, structural engineers and students to see if a steel needs a preheat, to compare heats of steel from their mill certificates, and to plan the work before the qualified procedure is written or checked.

Good to know

Take the composition from the mill certificate of the heat that you weld and not from a general table. Heat the plate on both sides of the joint for a distance of at least 3 in (75 mm) or the thickness of the plate, whichever is larger, and measure the temperature on the face away from the flame. Keep the interpass temperature under the limit of the procedure, and let the weld cool slowly under a blanket on thick plates.

The welding heat input calculator gives the energy of an arc weld, the fillet weld strength calculator gives the capacity of a fillet weld, the steel tension member capacity calculator checks a tension member and the Charpy impact energy calculator gives the energy absorbed by a notched sample.

Frequently asked questions

What is the carbon equivalent?

The carbon equivalent turns the alloy content of a steel into a single number that shows how hard the weld and the heat-affected zone can become. The calculator uses the formula of the International Institute of Welding: carbon plus manganese over 6, plus chromium, molybdenum and vanadium over 5, plus nickel and copper over 15. A higher value means a greater risk of cold cracking.

Why does the thickness matter?

A thick plate takes the heat away from the weld quickly, so the weld cools fast and becomes hard and brittle. The calculator adds 0.5 % of the carbon equivalent for each millimeter of thickness. A thick plate therefore needs a higher preheat than a thin plate of the same steel, and the preheat also helps the hydrogen to leave the weld.

How is the preheat found?

The calculator uses a simple fit, the preheat in degrees Celsius is 350 times the square root of the total carbon equivalent minus 0.25. Below 0.25 no preheat is shown. The result is a starting point, and the code that governs your work, such as the structural welding code, gives the minimum preheat from tables for the steel, the thickness and the process.

What are the limits of the calculator?

The calculator does not include the hydrogen level of the electrodes, the restraint of the joint, the heat input, the ambient temperature, the interpass temperature or the stainless and special steels. Always follow the qualified welding procedure of the job, measure the preheat with a temperature stick or a contact thermometer, and keep the low-hydrogen electrodes dry.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.