Skip to content
Omnikalc

Cold-formed purlin span check calculator: bending and deflection

Enter the purlin spacing and span, the roof loads, the section modulus, the moment of inertia and the yield strength to get the moment, the allowable moment, the deflection and the ratios.

Updated on
Your inputs
ft

Value out of range

ft

Value out of range

psf

Value out of range

psf

Value out of range

in³

Value out of range

in⁴

Value out of range

ksi

Value out of range

Results

Ratio of the moment to the allowable

0.65

The bending strength is sufficient
Uniform load on the purlin
170 plf
Bending moment
13.28 kip-ft
Allowable bending moment
20.58 kip-ft
Deflection
1.27 in
Ratio of the deflection to L/180
0.76
The deflection is within L/180

The cold-formed purlin span check calculator gives the load on the purlin, the bending moment, the allowable moment, the deflection and the bending and deflection ratios of a simply supported roof purlin, from the spacing, the span, the loads and the section properties.

How the calculation works

  • Enter the purlin spacing, the span and the dead and snow or live loads of the roof.
  • Enter the section modulus, the moment of inertia and the yield strength of the purlin.
  • The calculator finds the load on the purlin, the bending moment, the allowable moment, the deflection and the two ratios.

Example

Purlins every 5 ft carry a roof of 4 psf dead load and 30 psf of snow, that is (4 + 30) × 5 = 170 plf. On a span of 25 ft, the moment is 170 × 25² / 8 = 13.28 kip-ft. A purlin with 7.5 in³ of section modulus at 55 ksi has an allowable moment of 7.5 × 55 / 1.67 / 12 = 20.58 kip-ft, so the ratio is 0.65. With 40 in⁴, the deflection is 1.27 in, against 25 × 12 / 180 = 1.67 in, a ratio of 0.76.

Why it matters

The calculator helps metal building designers, steel detailers, contractors and students to check a purlin quickly, to see how the spacing and the span change the stress and the deflection, and to compare several sections before looking at the tables of a manufacturer.

Good to know

Check the purlin for the uplift of the wind as well as for the gravity loads, and brace the flanges as the manufacturer says. Use the section properties of the table of the manufacturer, because the effective values are lower than the gross values. Fasten the roof sheeting well to the purlins and add the purlin bracing lines for long spans.

The roof truss calculator plans the trusses, the wood beam span calculator checks a timber beam, the hurricane tie-down uplift force calculator checks the uplift of the roof and the beam deflection calculator gives the deflection of other loads.

Frequently asked questions

What is a purlin?

A purlin is a horizontal beam that spans between the main frames or the rafters of a roof and supports the roof sheeting or the deck. In a metal building, the purlins are usually cold-formed steel sections, in the shape of a Z or a C, which are light and economical. They carry the roof load by bending to the frames, and they also brace the top flange of the rafters.

How is the bending checked?

The load on a purlin is the roof load, in pressure, times the spacing of the purlins, which gives a load per unit of length. For a simple span, the maximum moment is the load times the span squared divided by 8. The moment is compared with the allowable moment, which is the section modulus times the yield strength divided by a safety factor of 1.67 in the allowable stress design.

How is the deflection checked?

The deflection of a simple span under a uniform load is 5 times the load times the span to the fourth power divided by 384 times the modulus of elasticity of the steel times the moment of inertia. It is compared with a limit, often the span divided by 180 for a roof with a snow load, and the limit can be stricter for a ceiling or for a roof with a rigid finish.

What are the limits of the calculator?

The calculator treats the purlin as a simple span with a fully braced compression flange. It does not take into account the continuity at the laps of a Z-purlin, which reduces the moment, the lateral-torsional buckling, the uplift of the wind that puts the unbraced flange in compression, the web crippling at the supports, the biaxial bending on a sloped roof or the effective section of the cold-formed shape. The values of the section must come from the load tables of the manufacturer.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.