Skip to content
Omnikalc

Wood beam span calculator: longest span of a simply supported beam under a uniform load

Enter the section, the allowable stresses, the modulus, the load and the deflection limit to get the longest span for bending, shear and deflection.

Updated on
Your inputs
in

Value out of range

in

Value out of range

psi

Value out of range

psi

Value out of range

psi

Value out of range

lb/ft

Value out of range

Results

Longest span (all checks)

15.86 ft

Longest span for bending
16.65 ft
Longest span for shear
48.56 ft
Longest span for the deflection limit
15.86 ft
Limiting check (1 = bending, 2 = shear, 3 = deflection)
3
Deflection governs the span
Section modulus
49.91 in³
Moment of inertia
230.84 in⁴

The span of a wood beam is limited by its strength and by its stiffness. The wood beam span calculator gives the longest span of a simply supported rectangular beam under a uniform load for bending, shear and deflection, tells which check governs, and shows the section modulus and the moment of inertia.

How the calculation works

  • Enter the width and the depth of the beam section (the real dimensions, not the nominal ones).
  • Enter the allowable bending stress Fb, the allowable shear stress Fv and the modulus of elasticity E of the wood, with the adjustments for your case.
  • Enter the uniform load per foot, including the weight of the beam, and choose the deflection limit.
  • The calculator finds the longest span for three checks of a simply supported beam: bending L = √(8 Fb S / w), shear L = 4 Fv b d / (3 w) and deflection L = ∛(384 E I / (5 w n)). The shortest one governs.

Example

A beam of 3.5 × 9.25 in carries 120 lb/ft, with Fb = 1,000 psi, Fv = 135 psi and E = 1,400,000 psi. The section modulus is 49.91 in³ and the moment of inertia is 230.84 in⁴. The longest span is 16.65 ft for bending, 48.56 ft for shear and 15.86 ft for a deflection limit of L / 360. So deflection governs and the longest span is 15.86 ft.

Why it matters

The calculator helps homeowners, builders, carpenters and students to check a header, a beam or a joist before looking at the span tables, to compare sections and to see why a deeper beam is much stronger. It gives a quick answer for a project such as a deck, a garage or a floor, and shows which limit to work on.

Good to know

The calculator is for a simply supported rectangular beam of solid wood with a uniform load over the full span. Point loads, cantilevers, continuous beams, notches, holes, lateral buckling, bearing length and built-up beams with partial composite action are not included. The allowable values you enter must be correct for the species, the grade and the conditions. The results are an estimate and not a design, so a building official or an engineer must check a real structure.

The beam deflection calculator gives the deflection for a given load, the floor joist calculator checks floor framing, the section modulus calculator handles other shapes, and the moment of inertia calculator gives the stiffness of a section.

Frequently asked questions

How is the span of a beam found?

A simply supported beam under a uniform load has a maximum bending moment of w L² / 8 at the middle and a maximum shear of w L / 2 at the supports. The span is limited by the allowable bending stress, by the allowable shear stress and by the deflection. The calculator computes the longest span for each of these three checks, and the smallest value is the span you can use.

Why does deflection often govern?

Wood is flexible, and a floor that is strong enough can still feel bouncy or crack the plaster. The deflection limit L / 360 is a common one for floors, L / 240 for roofs and L / 480 for finishes that crack easily. For beams of normal depth and a span of more than about 10 ft, the deflection check is often the limit, and a deeper beam helps much more than a wider one.

What stress values should I use?

Use the allowable (design) values for the species and grade from the building code tables or the lumber supplier, with the adjustment factors for the load duration, the moisture, the size and the repetitive use. Typical values for dimension lumber are 700 to 1,500 psi for bending, 90 to 180 psi for shear and 1.2 to 1.9 million psi for the modulus.

Is the weight of the beam included?

The load that you enter must include the weight of the beam. A 3.5 by 9.25 in section of wood weighs about 8 lb/ft. Add the dead load of the floor or the roof and the live load, for example 40 psf of live load on a 4 ft wide strip makes 160 lb/ft. If you hesitate, ask an engineer, since a failure of a beam is a safety problem.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.