Skip to content
Omnikalc

Composite beam transformed section calculator

Enter the steel beam properties, the slab thickness, the span and the beam spacing to get the effective width, the modular ratio, the neutral axis and the transformed moment of inertia of the composite beam.

Updated on
Your inputs
in²

Value out of range

in⁴

Value out of range

in

Value out of range

in

Value out of range

ft

Value out of range

ft

Value out of range

psi

Value out of range

Results

Transformed moment of inertia

1,747 in⁴

Effective width of the slab
90.0 in
Modular ratio n = Es / Ec
8.04
Neutral axis above the bottom of the steel
18.44 in
Gain over the steel beam alone
3.43
Reduction of the deflection
70.8 %
Section modulus at the bottom of the steel
95 in³

The composite beam transformed section calculator converts the concrete slab into steel with the modular ratio and gives the effective width, the neutral axis and the transformed moment of inertia of a composite beam.

How the calculation works

  • Enter the area, moment of inertia and depth of the steel beam, the thickness of the slab and the concrete strength.
  • Enter the span and the spacing of the beams to get the effective width of the slab.
  • The calculator transforms the slab into steel with the modular ratio and gives the neutral axis, the transformed moment of inertia and the section modulus.

Example

A steel beam with 10.3 in² and 510 in⁴, 17.7 in deep, carries a 5 in slab of 4,000 psi concrete. The effective width is the smaller of 30 ft / 4 = 90 in and the spacing of 96 in, so 90 in. With Ec = 57 √4000 = 3,605 ksi, the modular ratio is 8.04 and the transformed slab is 11.19 in wide. The neutral axis is 18.44 in above the bottom of the steel and the transformed moment of inertia is 1,747 in⁴, 3.43 times the bare steel, which cuts the deflection by 71 %.

Why it matters

The calculator helps structural engineers, detailers and students to estimate the stiffness of a composite floor beam, to check the deflection under the live load and to see how much the slab adds to the bare steel beam.

Good to know

Use the full composite moment of inertia only if the number of shear studs gives full composite action. With fewer studs, the stiffness is lower, and AISC uses a lower bound moment of inertia in the deflection check. Enter the dimensions of the steel section from the shape tables and the thickness of the concrete above the deck, not the total thickness of the slab with the ribs. The modular ratio changes with the concrete strength and the weight of the concrete, so take the one of your mix. For a long-term load, use a modular ratio larger by two or three.

The shear stud calculator counts the studs for the composite action, the beam deflection calculator gives the deflection from the moment of inertia, the moment of inertia calculator gives the properties of simple shapes and the section modulus calculator converts the moment of inertia to bending stress.

Frequently asked questions

What is the transformed section?

The transformed section replaces the concrete of the slab with an equivalent area of steel, found by dividing the width of the slab by the modular ratio n = Es / Ec. The beam is then a single steel section, and the usual formulas for the neutral axis, the moment of inertia and the stress can be used. The stress in the concrete is the stress in the transformed area times n.

How do I find the effective width?

The slab does not work across its whole width, because the stress falls away from the beam. The AISC specification takes, on each side of the beam, the smallest of one eighth of the span, half the distance to the next beam and the distance to the edge of the slab. For an interior beam that gives the smaller of a quarter of the span and the spacing.

Can I use this for deflection?

Yes. The transformed moment of inertia is for full composite action and is used for the live load deflection. For the dead load on a beam that is shored or not, and for long-term loads, creep makes the slab softer, so many designers use a modular ratio of two to three times larger, or a lower-bound moment of inertia.

What does the calculator leave out?

The calculator leaves out the metal deck, the haunch, the concrete in the ribs, the reinforcement of the slab, the partial composite action when there are few studs and the steel beam load carrying before the concrete hardens. It computes the elastic properties of a solid slab.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.