Skip to content
Omnikalc

Precast manhole section count and height calculator

Enter the depth, the heights of the base and the cone, the minimum rings, the barrel length and the weights to get the number of barrel sections, the rings, the total weight and the heaviest piece.

Updated on
Your inputs
ft

Value out of range

ft

Value out of range

ft

Value out of range

ft

Value out of range

lb/ft

Value out of range

lb

Value out of range

lb

Value out of range

Results

Stack of adjusting rings

6 in

The adjusting rings are within the usual limit
Number of barrel sections
2
Height of the barrels
8.0 ft
Total weight
12,600 lb
Heaviest piece
3,800 lb

The precast manhole section count and height calculator gives the number of barrel sections, the height of the barrels, the stack of adjusting rings, the total weight and the heaviest piece of a precast concrete manhole, from the depth, the heights of the base and of the cone and the length of the barrel sections.

How the calculation works

  • Enter the depth of the manhole from the invert to the rim.
  • Enter the height of the base section and of the cone, the minimum rings and the length of the barrel sections.
  • Enter the weights to get the number of sections, the stack of rings, the total weight and the heaviest piece.

Example

A manhole is 14 ft deep, with a base section of 3 ft, a cone of 2.5 ft and at least 0.5 ft of rings. The space for the barrels is 14 − 3 − 2.5 − 0.5 = 8 ft, so 2 barrel sections of 4 ft are used, that is 8.0 ft. The rings make up 14 − 3 − 2.5 − 8 = 0.5 ft, that is 6 in. The total weight is 3,800 + 2,000 + 850 × 8 = 12,600 lb, and the heaviest piece is the base, with 3,800 lb.

Why it matters

The calculator helps utility contractors, estimators, inspectors and students to order the sections of a manhole for a given depth, to check the stack of the rings, and to plan the crane for the heaviest piece of the delivery.

Good to know

Check the invert and the final grade of the road before you order the sections, and the dimensions of the sections with the supplier. Set the base on a level and compacted bed, seal every joint with its gasket, and keep the stack of the rings under the limit of the agency. Use a crane which is rated for the heaviest piece at the radius of the lift.

The pipe trench bedding and backfill calculator gives the volumes of the trench, the thrust block calculator sizes the block of a pressure pipe, the wet well volume calculator sizes a lift station and the crane mat bearing pressure calculator checks the ground under a crane.

Frequently asked questions

What are the parts of a precast manhole?

A precast concrete manhole is made of a base section with the floor and the first wall, barrel sections of standard heights, a cone or a flat top slab, and adjusting rings, called grade rings, which bring the top to the level of the rim. The joints between the sections are sealed with rubber gaskets or with mastic. The frame and the cover are set on the top ring.

How is the number of sections found?

The depth from the invert to the rim is the sum of the heights of the base, the barrel sections, the cone and the rings. The cone and the base have a fixed height, and the rings are limited, so the barrel sections fill the rest. The calculator takes the whole number of barrel sections which leaves the minimum height for the rings, and the remainder goes to the rings.

Why are the adjusting rings limited?

The adjusting rings are used to fit the rim to the final grade of the road, and too many rings make the top of the manhole unstable and a weak point for the infiltration of water. Many agencies limit the stack of rings to 12 in (300 mm) or less. If the stack is higher, a shorter barrel section is used to reduce it.

What are the limits of the calculator?

The calculator uses standard heights that you enter, and one type of barrel. It does not take into account the eccentric cone, the drop connections, the steps, the channel in the base, the buoyancy in a high groundwater, the traffic load or the diameter of the manhole. The sections must be ordered from the supplier with the right model and the tolerance of the joints.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.