Skip to content
Omnikalc

Dovetail joint calculator: how wide are the tails and pins?

Enter the board width, the number of tails, the tail to pin ratio and the slope to get the pitch, the width of tails and pins and the angle of the sides.

Updated on
Your inputs

Value out of range

Value out of range

Value out of range

Value out of range

Results

Tail width at mid-thickness

1.000 in

Pitch from one tail to the next
1.500 in
Pin width at mid-thickness
0.500 in
Width of a half-pin at each edge
0.250 in
Tail width at its wide end
1.125 in
Tail width at its narrow end
0.875 in
Angle of the sides from vertical
9.46 °

A well-spaced row of dovetails looks like a sign of skill, and the layout is mostly simple arithmetic. This dovetail joint calculator takes the board width, the number of tails, the tail to pin ratio, the board thickness and the slope to give the pitch, the width of the tails and pins, the half-pin at each edge, the width of a tail at its wide and narrow ends and the angle of the sides.

How the calculation works

  • Pitch = board width ÷ number of tails. Each pitch holds one tail and one pin, and the layout ends with a half-pin on each edge.
  • Pin width = board width ÷ (tails × (1 + ratio)), where the ratio is the tail width divided by the pin width at mid-thickness. Tail width = ratio × pin width, and a half-pin is half of a pin.
  • Wide and narrow ends: the sides slope by the thickness ÷ the slope number on each edge, so the tail is wider by thickness ÷ slope at one face and narrower by the same amount at the other.
  • Angle = arctan(1 ÷ slope). A slope of 1:6 is 9.46° and 1:8 is 7.13° from the line of the board.

Example

A board 6 in wide, 0.75 in thick, gets 4 tails with tails twice as wide as the pins and a 1:6 slope. The pitch is 6 ÷ 4 = 1.5 in. The pin width is 6 ÷ (4 × 3) = 0.5 in and the tail is 1.0 in at mid-thickness, with half-pins of 0.25 in at the edges. The sides lean by 0.75 ÷ 6 = 0.125 in, so the tail is 1.125 in at its wide end and 0.875 in at its narrow end. The angle is 9.46°.

Why it matters

Woodworkers use the numbers to mark out the joint with a marking gauge and dividers before they cut by hand or set up a jig. Planning the layout on paper avoids pins that are too thin at the edges and joints that look unbalanced.

Good to know

The widths are measured at mid-thickness, where the layout is drawn, and the real tails are wider on one face and narrower on the other. Saw kerf, the thickness of the marking line and the fit are not included, so cut slightly to the waste side and pare to the line. Hand-cut dovetails depend on the skill of the woodworker, and a jig may set its own spacing.

The board feet calculator estimates how much lumber a project needs and the wood weight calculator estimates the weight of the finished piece.

Frequently asked questions

What is a dovetail joint?

A dovetail joint is a woodworking joint in which wedge-shaped tails on one board lock into matching sockets between pins on another. Because the tails flare, the joint resists being pulled apart, which is why it has been used for drawers, boxes and chests for centuries.

What slope should I use?

The slope is the ratio of the sideways run to the length of the side. Common ratios are 1:6 for softwood and 1:8 for hardwood, which is about 9.5° and 7.1°. A steeper slope grips better but leaves the tails with short grain at the corners, which can break in hard woods.

How many tails should I cut?

It depends on the width of the board and the look you want. For a drawer side, 3 to 5 tails are common, and a fine box may have many more. The layout should leave a half-pin at each edge that is not too thin, since a half-pin that is too narrow can split.

Why use a ratio between tails and pins?

The ratio gives the character of the joint. Pins as wide as the tails look sturdy, while tails that are two to three times wider than the pins look refined. The calculator spreads the ratio evenly so that the tails and pins fill the whole width.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.