Skip to content
Omnikalc

Elastomeric bearing pad calculator: check a steel-reinforced bridge bearing under load and movement

Enter the load, the pad size, the elastomer layers, the shear modulus and the movement to get the shape factor, the compressive stress and its limit, and the shear strain over the limit of 0.5.

Updated on
Your inputs
kips

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

Value out of range

in

Value out of range

Results

Compressive stress over allowable

0.55

The compressive stress is within the allowable value
Average compressive stress
0.625 ksi
Shape factor S of an interior layer
6.86
Allowable compressive stress, 1.66 G S (limit 1.6 ksi)
1.138 ksi
Shear strain over the limit of 0.5
0.80
The shear strain is within the limit

The elastomeric bearing pad calculator checks a steel-reinforced elastomeric bearing of a bridge from the load, the pad size, the elastomer layers, the shear modulus and the movement: the shape factor, the compressive stress against its limit and the shear strain against the limit of 0.5.

How the calculation works

  • Enter the vertical load on the bearing and the length and width of the pad, with the length in the direction of the girder movement.
  • Enter the thickness of one interior elastomer layer and the number of layers, then the shear modulus G of the rubber.
  • Enter the horizontal movement of the girder at the bearing from temperature, creep and shrinkage.
  • The calculator finds the shape factor S = L W / (2 t (L + W)), the compressive stress against 1.66 G S, and the shear strain Δ / hrt against the limit of 0.5.

Example

A steel-reinforced bearing of 12 in × 16 in carries 120 kips and has 4 interior layers of 0.5 in with G = 0.10 ksi. The compressive stress is 120 / 192 = 0.625 ksi. The shape factor is 192 / (2 × 0.5 × 28) = 6.86, so the allowable stress is 1.66 × 0.10 × 6.86 = 1.138 ksi, and the ratio is 0.55. The rubber thickness is 4 × 0.5 = 2.0 in, so a movement of 0.8 in gives a shear strain of 0.4, which is 0.80 of the limit of 0.5.

Why it matters

The calculator helps bridge engineers, designers and students to size a bearing pad in a preliminary design, to see the balance between the plan size and the rubber thickness and to check that the movements are within the limits. It reproduces the main checks of the AASHTO specification in a simple tool.

Good to know

Take the load without the live load impact where the specification says so, and use the maximum design movement from the thermal range, the creep and the shrinkage. Use the manufacturer’s value of G, and the layer thickness of the actual pad. Complete the design with the rotation check, the stability and the anchorage. The bridge owner’s standard governs.

The thermal expansion calculator gives the girder movement, the pipe expansion loop calculator covers expansion in pipes, the beam bearing length calculator covers bearing on supports and the base plate size calculator covers steel base plates.

Frequently asked questions

What is an elastomeric bearing?

An elastomeric bearing is a pad of rubber, natural or neoprene, that is placed between a bridge girder and its support. It transmits the vertical load by compression, and it allows the horizontal movement of the girder from the temperature, the creep and the shrinkage, and the rotation of the end, by the shear and the bending of the rubber. Steel plates inside the pad prevent the bulging of the rubber and make it stiffer under load.

What is the shape factor?

The shape factor S is the ratio of the loaded area of one layer to the area of its free surface that can bulge: S = L W / (2 t (L + W)). A high shape factor, a thin layer with a big plan area, makes a stiff pad under compression. The compressive stress allowed by AASHTO LRFD for steel-reinforced pads is 1.66 G S, with a maximum of 1.6 ksi (11 MPa), so thin layers give a higher capacity.

How is the shear checked?

The horizontal movement of the girder produces a shear strain in the rubber equal to the movement divided by the total thickness of the elastomer, hrt. To avoid the rolling over of the pad at the edges and the fatigue, AASHTO limits this strain to 0.5, so the total rubber thickness must be at least twice the maximum movement. A thicker pad takes more movement but is less stiff in compression, so the thickness and the plan size are balanced.

What does the calculator not include?

It uses the simplified Method B of the AASHTO LRFD specification for the compressive stress and the shear. A full design also checks the combined compression and rotation, the stability of the pad, the thickness of the steel plates, the anchorage and the friction against sliding. The properties of the rubber must come from the manufacturer, and a bridge engineer must make the final design.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.