Skip to content
Omnikalc

Beam bearing length calculator: how long a beam must bear on its support

Enter the end reaction of a steel beam, the concrete strength, the bearing width and the section properties to get the bearing length for the support and for the web, the governing length and the bearing stress.

Updated on
Your inputs
kips

Value out of range

ksi

Value out of range

in

Value out of range

ksi

Value out of range

in

Value out of range

in

Value out of range

Results

Bearing length rounded up to 1/4 in

2.75 in

Bearing length for the concrete or masonry support
2.55 in
Bearing length for web local yielding
0.75 in
Required bearing length
2.55 in
Bearing stress on the support at that length
2.05 ksi

A beam needs a bearing length long enough to avoid crushing the concrete or masonry below it and the web of the beam above it. The beam bearing length calculator computes both lengths from the end reaction, finds the governing length and gives the bearing stress.

How the calculation works

  • Enter the factored reaction at the end of the beam, the concrete strength f′c of the support and the width of the bearing area (the flange width or the plate width).
  • Enter the yield strength of the steel, the web thickness of the beam and the distance k from the outside of the flange to the toe of the web fillet, both from the section tables.
  • The calculator computes the length for the concrete bearing N = R / (φ × 0.85 f′c × B), with φ = 0.65 as in ACI 318, and for the web local yielding at an end: N = R / (Fy tw) − 2.5 k, with φ = 1.0 as in AISC 360.
  • The required bearing length is the larger value, and the tool rounds it up to the next quarter of an inch.

Example

A steel beam delivers a factored end reaction of 45 kips on a concrete wall with f′c = 4 ksi, on a bearing width of 8 in. The beam has Fy = 50 ksi, tw = 0.30 in and k = 0.9 in. The concrete bearing needs 45 / (0.65 × 0.85 × 4 × 8) = 2.55 in. The web local yielding needs 45 / (50 × 0.30) − 2.5 × 0.9 = 3.00 − 2.25 = 0.75 in. The concrete governs, so the required bearing length is 2.55 in, rounded up to 2.75 in, with a bearing stress of 2.05 ksi.

Why it matters

The calculator helps structural engineers, designers of residential and light commercial buildings, detailers and students to size the bearing of a steel beam on a wall, a pier or a footing, and to decide if a bearing plate is needed. It avoids the common error of resting a heavily loaded beam on a few inches of block.

Good to know

Use the factored reaction of the governing load combination. Add the tolerance of the erection to the length, and keep at least 3 in (75 mm) for a beam on masonry or concrete. When the stress is high, add a bearing plate and grout it. Remember to check the support itself, not only the beam.

The bolt shear capacity calculator checks the connection of the beam, the steel column capacity calculator checks the member that carries it, the beam deflection calculator checks its stiffness and the punching shear calculator checks concentrated loads on slabs.

Frequently asked questions

Why does a beam need a minimum bearing length?

The reaction of the beam is a concentrated load on the support below it. If the bearing length is too short, the stress on the concrete or the masonry crushes the support, and the thin web of the beam yields or crushes locally above the support. Both checks need a minimum length, and the larger one governs. A beam that bears on a wall also needs a bearing plate to spread the load.

What is the bearing strength of concrete?

ACI 318 gives the design bearing strength as φ × 0.85 × f′c × A1, with φ = 0.65, when the bearing area is not confined by a larger surface. If the supporting surface is wider than the loaded area on all sides, the strength can be raised by a factor up to 2, which this calculator does not use. Masonry has its own, lower, bearing stresses in TMS 402.

What is web local yielding?

The web of a steel beam can yield under a concentrated load, in the zone just above the support. The AISC 360 formula for a reaction at the end of a beam, at a distance from the end less than the depth of the beam, is Rn = Fy tw (2.5 k + N), with φ = 1.0. The load is assumed to spread at a slope of 2.5 to 1 from the flange to the toe of the web fillet.

What other checks are needed?

The calculator does not check the web crippling, which is a buckling of the web, and which needs the depth of the beam and the thickness of the flange. It does not check the bending of the bearing plate either, or the shear and the bearing of the wall below. Use it as a first check of the bearing length, then complete the checks in the design standard.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.