Skip to content
Omnikalc

Falling weight impact calculator: what happens when a weight drops on a beam

Enter the weight, the drop height and the properties of a simply supported beam to get the static deflection, the impact factor, the maximum deflection, the maximum stress and the ratio to the yield strength.

Updated on
Your inputs
lb

Value out of range

in

Value out of range

in

Value out of range

Msi

Value out of range

in⁴

Value out of range

in³

Value out of range

ksi

Value out of range

Results

Impact factor 1 + √(1 + 2h / δst)

20.46

Static deflection under the weight
0.0318 in
Maximum deflection under impact
0.650 in
Stress under the static weight
1.92 ksi
Maximum stress under impact
39.3 ksi
Maximum stress as a share of the yield strength
78.6 %
Below the yield strength with a margin

A falling weight hits a structure harder than the same weight at rest. The falling weight impact calculator gives the impact factor of a weight dropped on the middle of a simply supported beam, with the maximum deflection, the maximum stress and the ratio to the yield strength.

How the calculation works

  • Enter the falling weight, the height from which it drops onto the beam, and the span of the simply supported beam. The weight is dropped at midspan.
  • Enter the modulus, the moment of inertia and the section modulus of the beam, and its yield strength.
  • The calculator finds the static deflection δst = W L³ / (48 E I) that the weight would cause if it were placed slowly, then the impact factor 1 + √(1 + 2h / δst), the ratio of the dynamic to the static effect.
  • It multiplies the static deflection and stress by the impact factor to get the maximum deflection and the maximum stress, and compares the stress with the yield strength.

Example

A 200 lb weight drops 6 in onto the middle of a steel beam of 96 in span, with E = 29 Msi, I = 4 in⁴ and S = 2.5 in³. The static deflection is 200 × 96³ / (48 × 29,000,000 × 4) = 0.0318 in. The impact factor is 1 + √(1 + 2 × 6 / 0.0318) = 20.46. The maximum deflection is 0.650 in. The static stress is 1.92 ksi, so the maximum stress is 39.3 ksi, which is 78.6% of the 50 ksi yield strength.

Why it matters

The calculator helps structural and mechanical engineers, safety engineers, builders and students to estimate the effect of a dropped load on a beam, a platform, a lifting frame or a floor, and to see why a drop of a few inches can multiply the stress by ten or more. It supports the design of guards, supports and falling object protection.

Good to know

Do not use the static design loads for a drop. Compute the impact factor, then check the stress and the deflection with it. Remember that the factor is higher for a stiffer beam. Add a cushion or a longer travel to absorb the energy when the stress is close to the yield. Check the connection and the supports too, not only the beam.

The Charpy impact energy calculator covers the toughness of materials, the beam deflection calculator gives the static deflections, the spring-mass calculator covers vibration and the section modulus calculator gives S.

Frequently asked questions

What is the impact factor?

A weight that is dropped from a height loads a structure much more than the same weight placed slowly. The impact factor is the ratio of the maximum dynamic deflection, or stress, to the static one. For a weight dropped from a height h on a structure of static deflection δst, the energy balance gives 1 + √(1 + 2h / δst). If the weight is applied suddenly with no drop (h = 0), the factor is 2.

How does the calculation work?

The potential energy of the weight, W (h + δmax), is converted into the strain energy of the beam, 1/2 k δmax², where k is the stiffness of the beam, W / δst. Solving the quadratic equation for δmax gives δmax = δst [1 + √(1 + 2h / δst)]. The stress is proportional to the deflection for a linear elastic beam, so it is multiplied by the same factor.

What makes the impact worse?

A stiff structure has a small static deflection, so a given drop height gives a large impact factor. A taller drop also raises it. This is why a stiff beam does not always take an impact better: it takes the same energy over a smaller deflection and so with a larger force. A flexible element, such as a spring, a cushion or a wooden beam, absorbs the energy with a lower force.

What are the limits of this calculator?

The model assumes that the beam is linear elastic, that the mass of the beam is negligible, that the weight does not bounce and that all the energy goes into the bending of the beam. In practice, part of the energy goes into the local deformation at the contact, the vibration and the supports, so the result is conservative. For a heavy beam or a very short impact, use a dynamic analysis. For yield or a plastic design, use an energy method.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.