Skip to content
Omnikalc

Charpy impact energy calculator: absorbed energy from the pendulum angles

Enter the capacity of the Charpy pendulum, the release angle and the angle reached after the break to get the energy absorbed by the specimen, its share of the capacity and the impact energy per area.

Updated on
Your inputs
ft·lbf

Value out of range

°

Value out of range

°

Value out of range

in²

Value out of range

Results

Energy absorbed by the specimen

57.6 ft·lbf

Above the usual requirement of 20 ft·lbf (27 J)
Share of the machine capacity
24.0%
Within the valid range of the machine
Impact energy per area of the ligament
464.7 ft·lbf/in²
Energy left in the pendulum
182.4 ft·lbf

The Charpy impact test breaks a notched specimen with a pendulum, and the energy absorbed shows the toughness of the material. The Charpy impact energy calculator computes the energy absorbed from the angles of the pendulum, its share of the capacity of the machine and the energy per area of the ligament.

How the calculation works

  • Enter the energy capacity of the pendulum, which is the potential energy at the release angle, and the release angle (usually about 140 to 150°, measured from the lowest position).
  • Enter the angle reached by the pendulum after it has broken the specimen, read on the dial of the machine.
  • Enter the area of the ligament under the notch, the cross-section of the specimen that breaks (about 0.124 in² or 80 mm² for the standard 10 × 10 mm specimen with a 2 mm notch).
  • The energy absorbed is the loss of potential energy of the pendulum: E = E0 (cos β − cos α) / (1 − cos α).

Example

A Charpy machine has a capacity of 240 ft·lbf and a release angle of 140°. After breaking the specimen, the pendulum rises to 110°. The energy absorbed is 240 × (cos 110° − cos 140°) / (1 − cos 140°) = 240 × (−0.3420 + 0.7660) / 1.7660 = 57.6 ft·lbf. This is 24.0% of the capacity, in the valid range. With a ligament of 0.124 in², the impact energy per area is 57.6 / 0.124 = 464.7 ft·lbf/in². The pendulum keeps 182.4 ft·lbf.

Why it matters

The calculator helps materials students, quality technicians and engineers to compute or check the Charpy energy from the readings of the machine, to compare specimens of different section, and to see if the test is within the valid range of the pendulum. It also explains the physics of the dial.

Good to know

Test at the temperature required by the specification, and at least three specimens. Keep the specimen at the test temperature until a few seconds before the impact, since it warms quickly. Report the energy together with the temperature, the notch type and the specimen size. If the result is above 80% of the capacity, use a bigger machine.

The Brinell hardness calculator gives another mechanical property, the Larson-Miller calculator covers creep life at high temperature, the critical crack size calculator links toughness and fracture and the pendulum calculator gives the physics of the swing.

Frequently asked questions

What is the Charpy impact test?

The Charpy test measures the energy that a notched specimen absorbs when a pendulum hits and breaks it. It shows the toughness of a material and its ductile-to-brittle transition: a steel can absorb a lot of energy at room temperature and break almost without any at low temperature. It is used to qualify steels for bridges, pressure vessels, pipelines and ships, and tests are made at several temperatures.

How is the absorbed energy computed?

The pendulum is released from a height that gives it the energy E0 = m g L (1 − cos α). After the break, it rises only to the angle β, and its energy is m g L (1 − cos β). The difference, E = m g L (cos β − cos α) = E0 (cos β − cos α) / (1 − cos α), is the energy absorbed by the specimen. Real machines correct this for the friction and the air drag, which the dial often does.

What is a good Charpy value?

A common requirement is 20 ft·lbf (27 J) at a specified temperature, for a full-size specimen. For pressure vessels and low-temperature service, the codes ask for higher values, such as 40 J. The standard specimen is 10 × 10 mm with a V-notch of 2 mm. Reduced-size specimens, such as 10 × 5 mm, absorb less energy, and their results must be corrected.

Why must the energy stay under 80% of the capacity?

If the specimen absorbs most of the energy of the pendulum, the speed at the end of the break is low and the test is no longer an impact at constant speed. The ASTM E23 and ISO 148 standards say that a result above 80% of the capacity is only approximate and must be reported as such. Use a machine with a higher capacity for tough materials.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.