Skip to content
Omnikalc

Hydraulic motor torque calculator: what a hydraulic motor delivers

Enter the displacement, the pressure drop, the flow and the efficiencies of a hydraulic motor to get the output torque, the speed, the output power, the overall efficiency and the hydraulic power supplied.

Updated on
Your inputs
in³/rev

Value out of range

psi

Value out of range

gpm

Value out of range

%

Value out of range

%

Value out of range

Results

Output torque T = D Δp ηm / 2π

119.4 lb-ft

Output speed N = Q ηv / D
1,097 rpm
Output power
24.9 hp
Overall efficiency ηm ηv
85.5 %
Hydraulic power supplied
29.2 hp

A hydraulic motor converts oil pressure and flow into torque and speed. The hydraulic motor torque calculator gives the output torque, the speed, the output power, the overall efficiency and the hydraulic power from the displacement, the pressure drop and the flow.

How the calculation works

  • Enter the displacement of the motor in cubic inches per revolution, the pressure drop across its ports and the flow rate that the pump supplies.
  • Enter the mechanical efficiency (torque efficiency) and the volumetric efficiency, usually 90% to 95% for a gear or piston motor in good condition.
  • The calculator computes the output torque T = D × Δp × ηm / 2π and the output speed N = Q × ηv / D, where the flow is converted to cubic inches per minute (1 gpm = 231 in³/min).
  • It gives the output power, the overall efficiency and the hydraulic power supplied, to compare the shaft with the pump.

Example

A hydraulic motor of 4.0 in³/rev runs with a pressure drop of 2,500 psi and a flow of 20 gpm, with a mechanical efficiency of 90% and a volumetric efficiency of 95%. The output torque is 4.0 × 2,500 × 0.90 / (2π) = 1,432 lb-in = 119.4 lb-ft. The speed is 20 × 231 × 0.95 / 4.0 = 1,097 rpm. The output power is 24.9 hp from a hydraulic power of 29.2 hp, an overall efficiency of 85.5%.

Why it matters

The calculator helps engineers, mechanics, designers of mobile and industrial machines, farmers and students to size a hydraulic motor and its pump for a winch, a conveyor, a wheel drive or an auger, and to check the torque and speed of a motor from its data plate. It avoids an undersized motor.

Good to know

Use the pressure drop across the motor, not the system pressure. Keep the pressure below the rated value of the motor and the relief valve above the working pressure. Check the efficiencies on the performance curve at the working point, not the best values. Allow for the starting torque and the loss at low speed.

The hydraulic press calculator covers cylinders, the pump power calculator sizes the motor that drives the pump, the motor speed calculator links the electric motor and the rpm and the pneumatic cylinder calculator covers the compressed-air equivalent.

Frequently asked questions

How is the torque of a hydraulic motor found?

A hydraulic motor turns a shaft by the pressure of the oil on its pistons, vanes or gears. For each revolution, it takes a fixed volume of oil, its displacement D. The theoretical torque is the pressure drop times the displacement divided by 2π: T = D Δp / 2π. The real torque is lower because of the friction, so it is multiplied by the mechanical efficiency ηm, which is usually 90% to 95%.

How is the speed found?

The speed depends only on the flow and the displacement: the theoretical speed is N = Q / D. Part of the oil leaks across the internal clearances without turning the shaft, so the real speed is lower, and it is multiplied by the volumetric efficiency ηv. The leakage grows with the pressure and with wear, and with a hot, thin oil, which makes the motor turn more slowly under load.

What are the types of hydraulic motors?

Gear motors are simple and cheap, for moderate pressures and speeds. Vane motors give smooth rotation. Axial and radial piston motors work at the highest pressures, up to 400 bar (6,000 psi), with the best efficiency and, for the radial type, a very high torque at low speed. Orbital (gerotor) motors give a high torque at low speed for winches and wheel drives.

What are the limits of this calculator?

It uses constant efficiencies, which in reality change with the speed, the pressure and the temperature. It does not include the back pressure on the return line, which reduces the pressure drop, the starting torque, usually lower than the running torque, or the case drain flow. For a design, use the performance curves of the manufacturer and size the pump and the relief valve for the maximum torque.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.