Skip to content
Omnikalc

Pocket hole screw calculator: which screw length and how many holes?

Enter the board thickness, the joint width and the number of joints to get the pocket screw length, the holes per joint and the screws to buy.

Updated on
Your inputs

Value out of range

Value out of range

%

Value out of range

Results

Screws to buy

36

Pocket screw length
1.25 in
Holes per joint
4
Spacing between holes
3.0 in
Boxes of 100
1

Pocket holes make a strong joint with only a drill and a jig, but the right screw length and the right number of holes depend on the thickness and the width of the joint. This pocket hole screw calculator takes the board thickness, the joint width, the number of joints and an extra for mistakes to give the pocket screw length, the holes per joint, the spacing between holes, the screws to buy and the boxes of 100.

How the calculation works

  • Screw length follows the thickness of the board that holds the pocket holes: 1/2 in takes a 1 in screw, 3/4 in a 1-1/4 in screw, 1 in a 1-1/2 in screw and 1-1/2 in a 2-1/2 in screw.
  • Holes per joint = the joint width ÷ 3.5 in, rounded up, with a minimum of 2. Every joint gets at least two holes so that the board cannot twist.
  • Spacing = joint width ÷ holes, and total screws = holes × joints × (1 + extra ÷ 100), rounded up.
  • Boxes = total screws ÷ 100, rounded up. Use a coarse thread screw for softwood and a fine thread screw for hardwood and plywood.

Example

You join 8 boards of 12 in wide with a thickness of 3/4 in. The right screw is 1-1/4 in long. A 12 in joint gets ⌈12 ÷ 3.5⌉ = 4 holes, one every 3 in. For 8 joints that is 32 screws, and with 10% extra you buy ⌈35.2⌉ = 36 screws, which is 1 box of 100.

Why it matters

Furniture makers and builders use the numbers to buy the right screws before a project, to set the jig and the drill collar and to avoid the common mistakes of screws that poke through the face or that are too short to hold.

Good to know

The screw lengths follow the usual recommendations of pocket hole systems, and your jig may give a different table, so check its guide. The spacing is a general rule and the strength depends on the wood, the glue and the load. Glue and clamps improve the joint. Always test on scrap, and use the depth stop and the drill that go with the jig.

The board feet calculator estimates lumber for the boards and the plywood sheets calculator plans cuts for panels.

Frequently asked questions

What is a pocket hole joint?

A pocket hole joint is made by drilling a hole at a shallow angle, about 15 degrees, into the edge or the back of one board, with a flat bottom for the screw head. The screw then goes into the second board and pulls the two together. It is quick, strong and hidden, which is why it is common in cabinets and face frames.

How do I choose the screw length?

The screw has to pass through the first board and bite well into the second without coming out the other side. For standard jigs, 1/2 inch material takes a 1 inch screw, 3/4 inch takes 1-1/4 inch, 1 inch takes 1-1/2 inch and 1-1/2 inch takes 2-1/2 inch. The thickness of the board with the holes is the one to use.

How many holes should I make?

Two holes in any joint is a minimum, to stop the boards from twisting. For wide boards add holes about every 3 to 4 inches. The calculator uses a spacing of at most 3.5 inches, and you can use fewer for light duty or more for heavy loads.

Coarse or fine thread?

Coarse thread screws are for softwood such as pine and cedar, since they grip well and do not strip. Fine thread screws are for hardwoods, such as maple and oak, and for plywood and MDF, where a coarse thread can split the wood. Using the wrong thread weakens the joint.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.