Skip to content
Omnikalc

Noise barrier insertion loss and Fresnel number calculator

Enter the heights and distances of the source, the barrier and the receiver, the frequency and the level to get the path difference, the insertion loss and the new level.

Updated on
Your inputs
ft

Value out of range

ft

Value out of range

ft

Value out of range

ft

Value out of range

ft

Value out of range

Hz

Value out of range

dBA

Value out of range

Results

Insertion loss of the barrier

12.4 dB

The barrier cuts the noise a lot (10 dB or more sounds half as loud)
Path difference over the barrier
0.82 ft
Fresnel number
0.73
Sound level at the receiver with the barrier
59.6 dBA

The noise barrier calculator gives the path difference, the Fresnel number and the insertion loss in decibels of a wall between a noise source and a receiver, and the sound level behind it.

How the calculation works

  • Enter the heights of the noise source, the receiver and the top of the barrier, and the distances from the barrier to the source and to the receiver.
  • Enter the frequency of the noise and the sound level at the receiver without the barrier.
  • The calculator gives the path difference, the Fresnel number, the insertion loss and the sound level behind the barrier.

Example

A truck exhaust at 8 ft is 40 ft from a barrier whose top is at 14 ft, and a receiver with ears at 5 ft stands 100 ft behind it. The sound that goes over the top travels 0.82 ft farther than the straight line, so at 500 Hz the Fresnel number is N = 2 δ f / c = 0.73. The insertion loss is 10 log10(3 + 20 N) = 12.4 dB, and a level of 72 dBA without the barrier drops to 59.6 dBA behind it.

Why it matters

The calculator helps acoustic consultants, highway and site engineers, contractors and neighbors to see what a barrier of a given height does, to compare heights and positions, and to check that a wall reaches the reduction that a permit or a noise limit requires.

Good to know

Put the barrier close to the source or close to the receiver, because the path difference is largest there. Keep the wall free of gaps, with sealed joints and a closed base, and make it heavy enough to block the sound that goes through it. A reduction of 5 dB is noticeable, 10 dB sounds half as loud, and more than 15 dB is hard to reach with a simple wall. A second check of the barrier at low and high frequencies shows how sensitive the result is.

The insertion loss calculator treats a filter in a circuit, the sound transmission class calculator rates the wall itself, the critical distance calculator compares direct and reverberant sound in a room and the noise exposure calculator gives the daily dose of a worker.

Frequently asked questions

What is the Fresnel number?

The Fresnel number N = 2 δ / λ compares the extra path δ of the sound that bends over the top of the barrier with the wavelength λ. A small number means the sound hardly notices the barrier, a large number means a deep acoustic shadow. The path difference is the sum of the two slanted distances from the source and the receiver to the top edge, minus the straight distance between them.

What formula gives the insertion loss?

The calculator uses the simple Maekawa relation for a point source and a long barrier, IL = 10 log10(3 + 20 N). A grazing line of sight, with N close to zero, gives about 5 dB, and the loss rises by about 3 dB each time the Fresnel number doubles. A practical limit of about 24 dB is applied, because sound that leaks through the wall, around its ends or reflects from the ground limits what a barrier can achieve.

Why does the frequency matter?

Low frequencies have long wavelengths and bend easily around an obstacle, so the same wall gives a smaller loss at 125 Hz than at 2,000 Hz. Traffic noise is dominated by 500 to 1,000 Hz, which is why a barrier is usually checked at 500 Hz. For a precise design, run the calculator at several octave bands and combine the results with the spectrum of the source.

What are the limits of the calculation?

The result applies to a barrier that is solid and heavy enough that sound does not pass through it, about 4 lb/ft² or more, and long enough that the sound around the ends is negligible. The barrier should be about five times as long as the distance to the receiver. Wind, temperature gradients and ground absorption change the real result by several dB.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.