Skip to content
Omnikalc

Permeable pavement calculator: depth of the stone reservoir under a porous pavement

Enter the design storm, the run-on ratio, the soil infiltration rate, the storm duration, the stone porosity and the pavement area to get the water to store, the reservoir depth, the drawdown time and the stone volume.

Updated on
Your inputs
in

Value out of range

Value out of range

in/h

Value out of range

h

Value out of range

Value out of range

ft²

Value out of range

Results

Required reservoir depth

12.9 in

Depth of water to store
4.50 in
Drawdown time
18.0 h
Drains within 48 h
Volume of stone in the reservoir
10,714 ft³

The permeable pavement calculator gives the depth of water to store, the stone reservoir depth, the drawdown time and the volume of stone under a porous pavement, from the design storm, the run-on ratio, the soil infiltration rate and the porosity of the stone.

How the calculation works

  • Enter the design storm depth, the run-on ratio (area that drains onto the pavement divided by the pavement area) and the storm duration.
  • Enter the measured infiltration rate of the subgrade, the porosity of the stone reservoir and the area of the pavement.
  • The calculator applies a safety factor of 2 to the infiltration rate, then finds the depth of water to store, the required reservoir depth, the drawdown time and the volume of stone.

Example

A permeable pavement of 10,000 ft² receives a 3 in storm in 6 h, with a run-on ratio of 1, a measured infiltration rate of 0.5 in/h and a stone porosity of 0.35. The design rate is 0.5 / 2 = 0.25 in/h. The water to store is 3 × (1 + 1) − 0.25 × 6 = 4.50 in. The reservoir depth is 4.5 / 0.35 = 12.9 in, the drawdown time is 4.5 / 0.25 = 18.0 h and the stone volume is 12.857 / 12 × 10,000 = 10,714 ft³.

Why it matters

The calculator helps civil engineers, landscape architects, site designers, municipal staff and students to size the reservoir under permeable asphalt, pervious concrete or permeable pavers in a first design, and to see how the soil rate and the run-on change the thickness of stone.

Good to know

Keep the subgrade uncompacted, protect the system from the sediment during the construction, and test the infiltration rate at the depth of the subgrade. Use the larger of the hydrologic depth and the structural depth. Plan the maintenance of the surface by vacuum sweeping.

The rain garden calculator sizes a planted infiltration basin, the rational method calculator gives the runoff peak, the water quality volume calculator gives the volume to treat and the detention time calculator checks a drawdown time.

Frequently asked questions

How is the reservoir depth found?

The water that falls on the pavement and the run-on from the neighboring areas goes through the surface into the stone reservoir. The depth to store is the storm depth times (1 + run-on ratio), minus the water that infiltrates in the soil during the storm. The reservoir depth is this depth divided by the porosity of the stone, which is about 0.30 to 0.40 for a clean, open graded aggregate.

Why use a safety factor on the infiltration rate?

The soil under a permeable pavement is loaded with fine particles during the life of the system, and the compaction during the construction also reduces the rate. A safety factor of 2 is common in design manuals, and some use 3 to 5 on the field rate. The calculator divides the measured rate by 2 for the storage and the drawdown calculation.

How long should the reservoir take to drain?

Most manuals require a drawdown of 48 to 72 hours, so that the reservoir is empty before the next storm and the stone does not stay saturated for long. A longer time means a risk for the frost heave of the base in cold areas and for the loss of strength of the subgrade. If the time is too long, add an underdrain with an upturned elbow, or increase the infiltration area.

What are the limits of the calculator?

The calculator does not check the structural thickness of the base for the traffic, the frost depth, the overflow, the geotextile and the clogging of the surface. The depth found is the hydrologic depth only, and the structural design may require more. The system should be designed by an engineer who knows the local standards.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.