Skip to content
Omnikalc

Pipe leakage test calculator: allowable make-up water for a hydrostatic test

Enter the length, the diameter, the average pressure, the duration and the make-up water to get the allowable leakage per hour, for the test and per 1,000 ft, and the ratio to the allowance.

Updated on
Your inputs
ft

Value out of range

in

Value out of range

psi

Value out of range

h

Value out of range

gal

Value out of range

Results

Allowable leakage per hour

2.48 gal/h

Allowable leakage for the test
4.97 gal
Allowable leakage per 1,000 ft per hour
0.99 gal/h
Ratio of the make-up water to the allowable
0.70
The leakage is within the allowance

The pipe leakage test calculator gives the allowable leakage per hour, the allowable leakage for the test, the allowable leakage per 1,000 ft and the ratio of the make-up water to the allowable for a hydrostatic test of a pressure pipe, from the length, the diameter and the test pressure.

How the calculation works

  • Enter the length of the pipe section tested, its nominal diameter and the average test pressure.
  • Enter the duration of the test and the make-up water that was added to hold the pressure.
  • The calculator finds the allowable leakage per hour and for the test, per 1,000 ft, and the ratio of the make-up water to the allowable.

Example

A pressure pipe of 12 in is tested over 2,500 ft at an average pressure of 150 psi. The allowable leakage is 2,500 × 12 × √150 / 148,000 = 2.48 gal/h, or 0.99 gal/h per 1,000 ft. For a test of 2 h, the allowable leakage is 4.97 gal. If 3.5 gal of make-up water was added, the ratio is 3.5 / 4.97 = 0.70, which passes the test.

Why it matters

The calculator helps pipeline contractors, inspectors, utility engineers and students to prepare the acceptance test of a new water main, to judge if the make-up water measured is acceptable and to compare the allowance for different lengths and diameters.

Good to know

Fill the line slowly from the low point with the air vents open, and let the pipe soak so that it is full of water before the test. Bleed all the air, bring the pressure up and hold it, and measure the make-up water with a calibrated meter or a graduated tank. Block the pipe ends and the valves with restraints that can take the test pressure, and keep the people away from the line during the test.

The hydrostatic test pressure calculator gives the pressure of the test, the pipe wall thickness calculator checks the pipe, the thrust block size calculator restrains the fittings and the leak rate pressure rise calculator handles the leaks in a closed volume.

Frequently asked questions

What is the leakage allowance of a pipe test?

In a hydrostatic leakage test, the pipe is filled with water and held at the test pressure for a given time, and the water added to hold the pressure is measured. This make-up water is the leakage of the joints and the fittings, and it must be less than an allowance given by the standard. The formula of the standard AWWA C600 for ductile iron pipe gives the allowance from the length, the diameter and the pressure.

What is the formula?

The allowance in gallons per hour is L = S × D × √P / 148,000, where S is the length of the pipe in feet, D is the nominal diameter in inches and P is the average test pressure in psi. The test is usually done at 150 % of the working pressure for 2 hours. The calculator converts the formula to SI units for the metric version, with the length in meters, the diameter in millimeters and the pressure in kPa.

What should be done if the pipe fails?

If the make-up water is over the allowance, the test is stopped and the leaks are found, by looking for the wet places at the joints, the valves and the hydrants, or by listening with a leak detector. The leaks are repaired, the air is bled from the line, and the test is done again. The air trapped in the line is a common cause of a false failure, so it must be removed before the test.

What are the limits of the calculator?

The calculator uses the formula of the standard and does not include the type of the pipe, because the allowances for other materials, such as PVC or polyethylene, are given by their own standards. It does not include the temperature changes, the absorption of the water by a lined pipe, the expansion of the pipe under the pressure or the air in the line. Follow the test procedure of the specification and the standard of the pipe.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.