Skip to content
Omnikalc

Rebar tie wire quantity and intersections calculator

Enter the area of the mat, the bar spacing, the layers, the share of the intersections tied and the wire per tie to get the number of ties, the tie wire and the labor hours.

Updated on
Your inputs
ft²

Value out of range

in

Value out of range

Value out of range

%

Value out of range

in

Value out of range

lb

Value out of range

Value out of range

Results

Ties required

5,000

Intersections in one layer
5,000
Length of tie wire
5,833 ft
Weight of tie wire
55.4 lb
Labor hours for the ties
11.1 h

The rebar tie wire calculator gives the intersections of a reinforcing mat, the number of ties, the length of tie wire, the weight of tie wire and the labor hours for the ties, from the area of the mat, the bar spacing, the number of layers and the share of the intersections tied.

How the calculation works

  • Enter the area of the mat, the spacing of the bars and the number of layers.
  • Enter the share of the intersections that are tied and the wire length per tie.
  • Enter the weight of the wire and the tying rate to get the ties, the wire and the labor hours.

Example

A slab of 5,000 ft² with bars at 12 in in both directions has 5,000 intersections in each layer. For 2 layers with 50 % of the intersections tied, that is 5,000 ties. At 14 in of wire per tie, the length is 5,000 × 14 / 12 = 5,833 ft, which weighs 5,833 × 9.5 / 1,000 = 55.4 lb. A worker who makes 450 ties an hour needs 11.1 h.

Why it matters

The calculator helps reinforcing steel contractors, estimators, site managers and students to order the tie wire, to plan the labor of the placing of a mat, and to compare the effect of a different bar spacing or of a different tying pattern on the time and the material.

Good to know

Order a margin of about 10 % for the waste of the wire and for the ties that break. Tie more intersections near the edges, at the splices and where the workers walk, because a loose bar can move during the pour. Use the pattern that the engineer allows, and keep the ends of the wire turned in, so that they do not touch the forms and cause rust spots on the surface.

The rebar chair spacing and quantity calculator gives the chairs under a mat, the rebar calculator gives the weight and the length of the bars, the rebar development length calculator gives the anchorage of a bar and the slab joint spacing calculator gives the joints of a slab on grade.

Frequently asked questions

How are the ties counted?

The bars of a mat cross at regular intervals, so the number of intersections in one layer is the area divided by the square of the spacing. Not every intersection is tied, because a tie at every second intersection in a staggered pattern is usually enough to hold the mat while the concrete is placed. Multiply by the number of layers and by the share of the intersections that are tied.

Which intersections must be tied?

The specification and the engineer decide. For the bottom mat of a slab, a tie at every second or third intersection is common, and for the walls, the columns and the top bars that must hold position under the foot traffic, more ties are needed. The edges of the mat and the splices are tied at every intersection, so use a higher share for a mat with many splices.

How much wire does a tie need?

A simple tie with a double wrap around the crossing of two bars uses a length of 12 to 16 in (30 to 40 cm) of 16.5 gauge wire. Smaller bars use less. The weight of the wire depends on its diameter, and the default of 9.5 lb per 1,000 ft is for a wire of about 0.06 in. Check the real wire on the coil that you buy.

What are the limits of the calculator?

The calculator uses a regular grid and the same pattern on all the layers. It does not include the chairs and the spacers, the splices, the lap lengths, the bends, the openings, the stirrups, the pre-tied cages or the tools that tie with a machine. Add a margin for the waste and the offcuts, and follow the placing drawings.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.