Skip to content
Omnikalc

Two-point lift with offset center of gravity and sling tension calculator

Enter the weight, the position of the center of gravity, the hook height and the sling limit to get the load on each pick point, the sling lengths and tensions and the ratio.

Updated on
Your inputs
lb

Value out of range

ft

Value out of range

ft

Value out of range

ft

Value out of range

lb

Value out of range

Results

Tension in the left sling

8,050 lb

Tension in the right sling

6,000 lb

Load on the left pick point
7,200 lb
Load on the right pick point
4,800 lb
Length of the left sling
8.94 ft
Length of the right sling
10.00 ft
Ratio of the highest tension to the limit
0.89
Slings within their working load limit

The two-point lift calculator gives the load on each pick point, the length and the tension of each sling and the ratio to the working load limit for a load with an off-center center of gravity, from its weight, the position of the center of gravity and the height of the hook.

How the calculation works

  • Enter the weight of the load and the horizontal distances from the two pick points to its center of gravity.
  • Enter the height of the hook above the pick points and the working load limit of the weakest sling.
  • The calculator finds the load on each pick point, the length and the tension of each sling and the ratio to the limit.

Example

A load of 12,000 lb has its center of gravity 4 ft from the left pick point and 6 ft from the right one. The pick points carry 12,000 × 6 / 10 = 7,200 lb on the left and 4,800 lb on the right. With the hook 8 ft above, the slings are 8.94 ft and 10.00 ft long, and the tensions are 7,200 × 8.94 / 8 = 8,050 lb and 4,800 × 10 / 8 = 6,000 lb. Against a limit of 9,000 lb the ratio is 0.89.

Why it matters

The calculator helps riggers, crane operators, lift planners, steel erectors and safety officers to plan a two-point lift of a beam, a tank or a precast piece, to see which sling is the most loaded, and to select the slings before the lift.

Good to know

Find the center of gravity first and put the hook above it, then choose the slings for the highest tension and not for half of the weight. Keep the angle of the slings above 45 degrees from the horizontal when you can, since a flat sling has a large tension. Add the weight of the spreader and the shackles to the load, and apply the dynamic factor required by your lift plan.

The sling angle calculator gives the tension of a sling at an angle, the tandem crane lift calculator shares a load between two cranes, the crane lift utilization calculator checks the lift against the chart and the tilt-up panel lifting insert calculator gives the load on the lifting inserts.

Frequently asked questions

How is the load shared between the pick points?

For a rigid load lifted at two points, with the hook above the center of gravity, the vertical load on each pick point is found by the moments about the other point. The pick point that is nearer to the center of gravity carries more load: the left one carries the weight times b / (a + b), where b is the distance of the right pick point from the center of gravity. If the center of gravity is in the middle, each point carries half.

Why are the sling tensions different?

Each sling carries the vertical load of its pick point divided by the sine of its angle from the horizontal. The sling with the larger horizontal offset is longer and flatter, so it has more tension for the same vertical load. The two horizontal components are equal, and they balance because the hook is directly above the center of gravity. The calculator uses the lengths of the slings that follow from the geometry.

What if the hook is not above the center of gravity?

The load will tilt until the center of gravity is below the hook. To lift a load level, choose the lengths of the slings so that the hook is above the center of gravity, or use a spreader beam with an adjustable pick point. The calculator assumes that the load hangs with the hook above the center of gravity and that the pick points are at the same height.

What does the calculator leave out?

The calculator does not include the dynamic factor of the lift, the weight of the rigging, the angle of the load when it is tilted, the capacity of the lifting lugs or the reduction of the sling capacity at the connections and the bends. Compare the tension with the working load limit of the sling at its angle, as given by the manufacturer, and have a qualified rigger check any critical lift.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.