Skip to content
Omnikalc

Tilt-up panel lifting calculator: insert load of a precast or tilt-up concrete panel

Enter the panel size, the unit weight, the suction factor, the number of inserts, the line angle and the insert capacity to get the weight, the load per insert, the line tension and the ratio.

Updated on
Your inputs
ft

Value out of range

ft

Value out of range

in

Value out of range

pcf

Value out of range

Value out of range

°

Value out of range

lb

Value out of range

Results

Tension in the lifting line

9,418 lb

Weight of the panel
43,500 lb
Vertical load per insert (with the factor)
8,156 lb
Ratio to the safe working load
0.78
The inserts have enough capacity

The tilt-up panel lifting calculator gives the weight of the panel, the vertical load per insert, the tension in the lifting line and the ratio to the safe working load of a tilt-up or precast concrete panel, from the size of the panel, the suction factor, the number of inserts and the angle of the line.

How the calculation works

  • Enter the width, the height and the thickness of the panel and the unit weight of the concrete.
  • Choose the suction and dynamic factor, enter the number of inserts, the angle of the lifting line and the safe working load of one insert.
  • The calculator finds the weight of the panel, the vertical load per insert, the tension in the lifting line and the ratio to the insert capacity.

Example

A panel of 20 ft by 24 ft and 7.25 in thick weighs 20 × 24 × 7.25 / 12 × 150 = 43,500 lb. With a factor of 1.5, the vertical load is 43,500 × 1.5 / 8 inserts = 8,156 lb per insert. The lifting line is at 60° above the horizontal, so the tension is 8,156 / sin 60° = 9,418 lb. For an insert with a safe working load of 12,000 lb, the ratio is 0.78.

Why it matters

The calculator helps tilt-up contractors, precast engineers, crane planners and students to check the lifting inserts of a panel, to compare the number of inserts and the angle of the rigging, and to prepare the lifting plan with the weight of the panel and the load of the crane.

Good to know

Check the concrete strength before the lift, apply a good bond breaker on the slab and use all the inserts with a spreader beam or equalizing rigging. Keep the lifting line at an angle of 60° or more, and verify that the panel will not crack during the lift with an engineered design of the reinforcement. Brace the panel at once after the erection, and keep the people out of the fall zone.

The sling angle calculator gives the tension in the rigging, the crane lift utilization calculator checks the chart and the wind, the concrete volume calculator gives the volume of the panel and the wind load calculator gives the wind pressure on the braced panel.

Frequently asked questions

How is the weight of a tilt-up panel calculated?

The weight is the volume of the panel times the unit weight of the concrete, about 150 pcf (24 kN/m³) for normal-weight concrete. Openings for doors and windows are deducted from the area, and the pilasters, the thickened edges and the blocks add weight. The weight of the panel must be known with a good accuracy, because it governs the choice of the crane and of the inserts.

Why is a suction factor used?

When a panel is lifted from the casting bed, the suction between the panel and the slab, and the bond of the concrete to the bed, add to the weight. The dynamic effect of the lift adds more load. The sum of these effects is given as a factor, often 1.2 to 1.7 times the weight, according to the bond breaker, the bed and the speed of the lift. The factor is applied to the weight to find the load on the inserts.

Why is the angle of the line important?

The inserts are loaded by the tension in the lifting line, which is the vertical load divided by the sine of the angle of the line above the horizontal. A flat angle increases the tension a lot, and the inserts are designed for a tension at a given angle. A spreader beam or a long line keeps the angle high and lowers the tension in the inserts and the sideways pull on the panel.

What are the limits of the calculator?

The calculator gives the average load per insert with an even sharing of the load. It does not include the bending of the panel during the lifting, which needs a check of the cracking and of the reinforcement, the edge distance and the concrete strength at the lift, the shear and the tension interaction of the insert, the rotation of the panel or the bracing after the erection. The design of the lift must follow the instructions of the insert manufacturer and the standard of the Tilt-Up Concrete Association.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.