Skip to content
Omnikalc

Tandem crane lift load sharing calculator for a two-crane pick

Enter the load, the rigging, the picking points, the center of gravity, the chart capacities and the derating factor to get the load on each crane and the utilizations.

Updated on
Your inputs
tons

Value out of range

tons

Value out of range

ft

Value out of range

ft

Value out of range

tons

Value out of range

tons

Value out of range

Value out of range

Results

Highest utilization

0.95

Little margin: check the plan, the radius and the real weights
Total weight to lift
41.5 tons
Load on crane 1
24.9 tons
Load on crane 2
16.6 tons
Utilization of crane 1
0.95
Little margin: check the plan, the radius and the real weights
Utilization of crane 2
0.74
Both cranes have a good margin

The tandem crane lift load sharing calculator gives the total weight, the load on each crane, the utilization of each crane and the highest utilization for a lift of one load with two cranes, from the weights, the picking points, the center of gravity and the chart capacities.

How the calculation works

  • Enter the weight of the load and of the rigging, the distance between the picking points and the position of the center of gravity.
  • Enter the chart capacity of each crane at its radius and the tandem derating factor.
  • The calculator finds the load on each crane, the utilization of each one and the highest utilization.

Example

A load of 40 tons with 1.5 tons of rigging weighs 41.5 tons. The picking points are 30 ft apart and the center of gravity is 12 ft from crane 1, so crane 1 carries 41.5 × 18 / 30 = 24.9 tons and crane 2 carries 16.6 tons. With a derating of 0.75, the allowable loads are 26.25 and 22.5 tons, so the utilizations are 0.95 and 0.74.

Why it matters

The calculator helps lift planners, crane operators, rigging supervisors and students to check the share of the load of two cranes before a tandem lift, to see how the center of gravity changes the loads, and to decide if the cranes and the radii are acceptable.

Good to know

Find the center of gravity of the load from the drawings and check it on the site, and add the weight of the rigging, the hooks and the spreader. Use the chart capacity at the real radius of each crane, with the outriggers extended as in the chart. Keep the hooks vertical, move the cranes slowly and in a coordinated way, and stop the lift if the plan is not followed.

The sling angle calculator gives the tension in the legs of the rigging, the crane mat bearing pressure calculator checks the ground, the tower crane calculator checks the load moment and the crane lift utilization calculator checks a single lift with the wind.

Frequently asked questions

What is a tandem lift?

A tandem lift is a lift of one load by two cranes at the same time, each one with its own hook. It is used for long or heavy loads, like a bridge girder, a steel truss or a precast element, that one crane cannot lift or cannot set in the position needed. The lift is more complex and more risky than a single lift, and it needs a written lift plan.

How is the load shared between the cranes?

The share of each crane depends on the position of the center of gravity between the two picking points. The crane which is nearer to the center of gravity carries the larger part, like the ends of a beam that carries a point load. The load of a crane is the total weight times the distance from the center of gravity to the other crane divided by the distance between the picking points.

Why is a derating factor used?

In a tandem lift, the cranes do not move perfectly together, the hooks are not exactly vertical, the load can shift and the real weights and the position of the center of gravity are not known exactly. A reduction of the chart capacity, often to 75 % of the chart for each crane, keeps a margin for these effects. Some plans use a smaller limit, and the rule of the company or of the standard must be followed.

What are the limits of the calculator?

The calculator shares a static load between two picking points in one line. It does not take into account the movement of the cranes, the angle of the slings, the wind, the swing, the soft ground, the boom deflection, the change of radius during the lift or the stability of the load itself. A tandem lift must be planned by a qualified person and led by a lift director.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.