Skip to content
Omnikalc

Router bit speed and feed calculator: tip speed and feed rate for your bit

Enter the bit diameter, the flutes, the chip load and the router speed to get the tip speed, the feed rate and the time to make a cut.

Updated on
Your inputs

Value out of range

Value out of range

rpm

Value out of range

Value out of range

Results

Feed rate

360.0 in/min

Tip speed
2,356 ft/min
Within the usual range for router bits
Tip speed in meters per second
12.0 m/s
Time for the cut
20.0 s

Router bits turn very fast, and a bit that is too fast or fed too slowly burns the wood, dulls quickly and can be dangerous. This router bit speed calculator takes the bit diameter, the number of flutes, the chip load, the router speed and the length of the cut to give the tip speed, the same in meters per second, the feed rate and the time for the cut, with a note on whether the tip speed is in the usual range.

How the calculation works

  • Tip speed = π × bit diameter × rpm ÷ 12, in feet per minute when the diameter is in inches. It is the speed of the cutting edge through the wood, and the same in meters per second is the tip speed in ft/min × 0.00508.
  • Feed rate = rpm × number of flutes × chip load per flute. It is the speed at which the router or the work moves, so that each cutting edge removes a chip of the chosen thickness.
  • Time for the cut = length of the cut ÷ feed rate.
  • Usual tip speeds for router bits are up to about 9,500 ft/min. Large diameter bits must run slower than small ones, because their tip speed grows with the diameter.

Example

A 1/2 in straight bit with 2 flutes runs at 18,000 rpm with a chip load of 0.010 in per flute. The tip speed is π × 0.5 × 18,000 ÷ 12 = 2,356 ft/min, or 12.0 m/s. The feed rate is 18,000 × 2 × 0.010 = 360 in/min, which means a cut of 10 ft (120 in) takes 120 ÷ 360 × 60 = 20 seconds.

Why it matters

Woodworkers use the figures to pick a safe router speed for large bits, to avoid burning cherry and maple and to set the feed on a CNC router. A rule such as ‘slow down for big bits’ becomes a number you can check.

Good to know

The ranges for tip speed and chip load are general guidance, and the limits of a bit are set by its maker, so always follow the maximum rpm marked on the bit. Dull bits, resin buildup, the species of wood and the depth of the cut change the right feed. Wear eye and hearing protection, hold the work securely and follow the safety rules of the router.

The feed rate calculator covers milling and CNC cutting, and the board feet calculator estimates the lumber for a project.

Frequently asked questions

Why does bit diameter matter for the speed of the router?

The tip of a large bit travels much faster than the tip of a small bit at the same rpm, since it covers a bigger circle. A 3 inch panel raising bit at 20,000 rpm would have a tip speed of about 15,700 ft/min, which is dangerous. That is why large bits must be used at a lower speed set on the router.

What is chip load?

Chip load is the thickness of the chip that each cutting edge removes. Too small a chip load rubs the wood and burns it, and too large a chip load tears the surface and strains the bit. Typical values are 0.005 to 0.020 inch for hardwood and 0.010 to 0.030 inch for softwood, but the maker of the bit gives the best guide.

What feed rate should I use?

The calculator gives the feed rate that follows from the speed, the flutes and the chip load. For a handheld router, a speed that is comfortable and gives a clean cut is usually slower than the figure for a CNC. Move the router steadily, and listen: burn marks mean the feed is too slow or the bit is dull.

Can I use the table for a CNC router?

Yes, the same relations apply to a CNC spindle, which usually works at 12,000 to 24,000 rpm. The feed rate is set in the software, and the calculator helps to check that the chip load stays in a good range for the material and the bit.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.