Skip to content
Omnikalc

Belt conveyor capacity calculator: capacity and motor power of a belt

Enter the load section, belt speed, material density, length and incline of a belt conveyor to get the capacity in tons per hour, the lift height, the friction and lifting power and the motor power required.

Updated on
Your inputs
ft²

Value out of range

ft/min

Value out of range

lb/ft³

Value out of range

°

Value out of range

ft

Value out of range

lb/ft

Value out of range

Value out of range

%

Value out of range

Results

Capacity

180.0 tons/h

Lift height
34.7 ft
Power to lift the material
6.31 hp
Power to overcome the friction
1.40 hp
Motor power required
8.57 hp
Share of the power used by friction
18.1 %
Most of the power goes into moving the material

The belt conveyor capacity calculator gives the tons per hour carried by a belt, its lift height and the motor power needed from the load section, the belt speed, the material density, the length and the incline. It shows how much of the power goes to lifting and how much to friction.

How the calculation works

  • Enter the cross-section area of the material on the belt, the belt speed, the bulk density of the material and the incline and length of the conveyor.
  • Enter the weight of the moving parts (belt and rollers) per foot, the friction factor of the idlers (about 0.02 to 0.04) and the drive efficiency.
  • The calculator finds the capacity = area × speed × density, and the lift height = length × sin(angle).
  • It adds the power to lift the material and the power to overcome the friction of the loaded belt, and gives the motor power after the drive efficiency.

Example

A conveyor carries material of 100 lb/ft³ in a section of 0.2 ft² at 300 ft/min. The capacity is 0.2 × 300 × 60 × 100 / 2,000 = 180.0 tons/h. The belt is 200 ft long at 10°, so the lift is 34.7 ft and lifting the load needs 6.31 hp. With 6 lb/ft of moving parts, a load of 20 lb/ft and a friction factor of 0.03, the friction power is 1.40 hp. With a 90% efficient drive, the motor must supply (6.31 + 1.40) / 0.9 = 8.57 hp.

Why it matters

The calculator helps plant and quarry engineers, farm and mining operators, material handling designers and students to size a belt drive, to check a motor on an existing belt and to compare options such as a faster or a wider belt. It is a quick first step before using a manufacturer’s selection program.

Good to know

Take the cross-section area from the manufacturer’s tables for the belt width and the troughing angle. Use a higher friction factor for dirty or cold conditions. Add a margin of 15 to 25% to the motor for starting the loaded belt. For belts longer than 1,000 ft, use the full method of the standard, which includes the belt tensions.

The motor current calculator checks the supply of the motor, the horsepower and torque calculator converts the power to shaft torque, the gear ratio calculator sizes the reducer and the density calculator converts mass and volume of the material.

Frequently asked questions

How is the capacity of a belt conveyor computed?

The capacity is the volume of material that passes a point each hour, which is the cross-section area of the load times the belt speed, times the bulk density to get the mass. The cross-section depends on the width of the belt, the troughing angle of the idlers and the surcharge angle of the material, and it is read from the belt manufacturer’s tables. The calculator takes this area directly so that it works for any belt.

How is the power of the motor found?

The power has two parts. The lifting power is the mass flow times gravity times the lift height, and it is zero on a horizontal belt. The friction power is the friction factor times the weight of the moving belt, rollers and load, times the belt speed, adjusted for the incline. The sum is divided by the efficiency of the drive. Real belts also have losses in the pulleys, skirts and cleaners, so keep a margin.

What friction factor should I use?

The friction factor of the idlers is about 0.02 for a well-aligned, lubricated conveyor in good conditions, and 0.03 to 0.04 for the usual industrial cases. It can rise above 0.05 for dirty, cold or badly aligned rollers. It is the main uncertain number for a long, flat conveyor, where friction takes most of the power. Check it with the measured current when the conveyor is running.

What is the maximum incline of a belt conveyor?

A smooth belt can usually carry dry material up to 15 to 18 degrees. Beyond that the material slides back and special belts with cleats or profiles are needed, which reach 30 degrees or more. The capacity also drops on steep inclines because the material rolls back, so the result of this calculator should be reduced with a factor given by the manufacturer for steep belts.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.