Skip to content
Omnikalc

Will your spring-mass system oscillate?

Enter the mass, the spring stiffness and the damping coefficient: get the damping ratio, the natural frequency, the critical damping, the overshoot and the settling time.

Updated on
Your inputs

Value out of range

N/m

Value out of range

N·s/m

Value out of range

Results

Damping ratio ζ

0.237

Underdamped: it overshoots and oscillates while the motion dies out
Natural frequency
1.258 Hz
Critical damping coefficient
6,325 N·s/m
Damped frequency
1.222 Hz
Overshoot after a step
46.4%
Settling time (2%)
2.13 s
Logarithmic decrement
1.534
Quality factor Q
2.11

A mass on a spring bounces up and down forever unless something takes energy out of the motion. That something is damping, from friction, air or a shock absorber. The damping ratio compares the damping actually present with the critical damping, the amount that just prevents oscillation. This calculator gives the damping ratio of a mass-spring-damper system, with the natural frequency, the overshoot, the settling time and the logarithmic decrement.

How the calculation works

  • Natural frequency: ω₀ = √(k ÷ m), and f₀ = ω₀ ÷ 2π
  • Critical damping: c_c = 2 × √(k × m)
  • Damping ratio: ζ = c ÷ c_c
  • Damped frequency: ω_d = ω₀ × √(1 − ζ²)
  • Overshoot = e^(−π × ζ ÷ √(1 − ζ²)) × 100%
  • Settling time (2%) ≈ 4 ÷ (ζ × ω₀)

Example

A quarter of a car, with a mass of 400 kg, rests on a spring of 25,000 N/m with a damper of 1,500 N·s/m. The natural frequency is 1.26 Hz and the critical damping is 6,325 N·s/m. The damping ratio is 0.237: the system is underdamped. After a bump it overshoots by 46% and settles in about 2.1 seconds.

Why it matters

Damping decides how a structure or machine reacts to a shock. Too little and it rings, too much and it responds sluggishly. Engineers tune suspensions, door closers, instruments, loudspeakers and electrical circuits to a target ratio. The same mathematics describes a series RLC circuit, where the resistance plays the role of the damper.

Good to know

The formulas apply to a linear system with a viscous damper, where the force is proportional to the speed. Real shock absorbers are often asymmetric and nonlinear, so the value is an average. For a ratio of exactly one the damped frequency is zero, and for values above one there is no oscillation, so the overshoot and the logarithmic decrement are shown as zero.

The spring-mass calculator gives the oscillation of an undamped spring, the compression spring calculator finds the stiffness of a coil spring, and the RLC impedance calculator covers the electrical equivalent.

Frequently asked questions

What is the damping ratio?

The ratio between the actual damping coefficient and the critical damping coefficient. It tells whether a mass on a spring will oscillate (below 1), return smoothly to rest without oscillating (above 1) or do so as fast as possible (equal to 1).

What is critical damping?

The smallest damping that prevents any oscillation. For a mass m on a spring of stiffness k it equals 2 × √(k × m). Door closers and gauge needles are often tuned close to it.

What damping ratio do cars use?

Passenger-car suspensions are usually set between about 0.2 and 0.4: a little overshoot is accepted for a softer ride and better tire contact. Competition cars use higher values.

How is the settling time estimated?

For an underdamped system, the envelope of the oscillation decays as e^(−ζ × ω₀ × t). The 2% settling time is when it falls below 2% of the initial value, about 4 ÷ (ζ × ω₀).

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.