Skip to content
Omnikalc

How much water will your channel carry?

Enter the width, depth, slope and roughness of a rectangular channel: get the flow area, the hydraulic radius, the velocity, the discharge and the Froude number.

Updated on
Your inputs

Value out of range

Value out of range

%

Value out of range

Value out of range

Results

Mean velocity

3.029 m/s

Discharge

4.222 m³/s

Flow area
1.394 m²
Hydraulic radius
0.416 m
Mean velocity in feet per second
9.94 ft/s
Discharge in cubic feet per second
149.1 cfs
Froude number
1.11
Supercritical flow (Froude number above 1): fast and shallow

The Manning equation is the standard way to estimate how fast water flows in an open channel: a ditch, a gutter, a culvert running partly full or a canal. It links the velocity to the shape of the channel, its slope and the roughness of its walls. This calculator applies it to a rectangular channel and returns the velocity, the discharge and the Froude number, in metric and US units.

How the calculation works

  • Flow area A = width × depth
  • Wetted perimeter P = width + 2 × depth
  • Hydraulic radius R = A ÷ P
  • Velocity V = (1 ÷ n) × R^(2/3) × S^(1/2), with S as the slope in metres per metre
  • Discharge Q = V × A, and Froude number = V ÷ √(g × depth)

Example

A concrete channel is 6 ft wide with 2.5 ft of water and a slope of 0.5%, with n = 0.013. The flow area is 1.39 m² (15 ft²) and the hydraulic radius is 0.416 m. The velocity is 3.03 m/s, or 9.9 ft/s, and the discharge is 4.22 m³/s, or about 149 cfs. The Froude number is 1.11, near critical, so the flow is fast and the surface unstable.

Where it is used

Civil engineers use it for drainage ditches, storm sewers, irrigation canals and streams. A landscaper uses it to check that a swale carries the runoff of a roof or a field, and a designer chooses a roughness and a slope that keep the velocity between a minimum that avoids silt and a maximum that avoids erosion. Typical limits are about 0.6 m/s to stop sediment and 1.5 to 2 m/s for earth channels.

Good to know

The formula assumes steady, uniform flow, meaning a constant depth along a long straight stretch. The roughness coefficient is the biggest source of error: vegetation, bends and debris raise it. The slope is the slope of the water surface, which equals the channel bed slope only for uniform flow. Natural streams vary a lot and need field data. For safety near floodwater, never rely on a calculation alone.

For pressurised pipes, use the pipe flow velocity and friction loss calculators. For the energy balance in a pipe, try the Bernoulli calculator, and for the flow regime, the Reynolds number calculator.

Frequently asked questions

What is the Manning equation?

An empirical formula for the average velocity of water in an open channel: V = (1 ÷ n) × R^(2/3) × S^(1/2), where R is the hydraulic radius, S the slope and n the roughness coefficient.

What is the hydraulic radius?

The flow area divided by the wetted perimeter, which is the length of channel boundary in contact with the water. A wider, shallower flow has a smaller hydraulic radius for the same area.

Does this work for pipes?

Yes, for pipes flowing partly full, but this calculator is set up for a rectangular channel. For a full pipe, the hydraulic radius is the diameter divided by four.

What is the Froude number?

The ratio of the flow speed to the speed of a surface wave. Below 1 the flow is calm and subcritical, and above 1 it is fast and supercritical, with hydraulic jumps when the two meet.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.