Skip to content
Omnikalc

Silica dust 8-hour TWA exposure calculator

Enter the dust concentration and the duration of each task and choose the respirator to get the 8-hour TWA, the percentage of the limit and the exposure inside the respirator.

Updated on
Your inputs
µg/m³

Value out of range

h

Value out of range

µg/m³

Value out of range

h

Value out of range

µg/m³

Value out of range

h

Value out of range

Results

Eight-hour TWA exposure

55.6 µg/m³

Total exposure of the shift
445 µg·h/m³
Percentage of the limit of 50 µg/m³
111 %
Above the limit of 50 µg/m³: reduce the dust or protect the worker
Exposure inside the respirator
5.6 µg/m³

The silica dust TWA calculator gives the total exposure of a shift, the 8-hour time-weighted average, the percentage of the limit of 50 µg/m³ and the exposure inside the respirator, from the concentration and the duration of up to three tasks.

How the calculation works

  • Enter the dust concentration and the duration of up to three tasks of the shift.
  • Choose the respirator that the worker wears.
  • The calculator finds the 8-hour TWA, the percentage of the limit and the exposure inside the respirator.

Example

A worker cuts block for 2.5 h at 120 µg/m³, works 3 h at 40 µg/m³ and 2.5 h at 10 µg/m³. The total is 120 × 2.5 + 40 × 3 + 10 × 2.5 = 445 µg·h/m³, and the 8-hour TWA is 445 / 8 = 55.6 µg/m³, that is 111 percent of the limit of 50 µg/m³. With a half-mask respirator of APF 10 the exposure inside the mask is 5.6 µg/m³.

Why it matters

The calculator helps safety officers, supervisors, contractors, hygienists and workers to estimate the exposure to silica dust during cutting, grinding and drilling of concrete and masonry, to see whether a task needs controls or a respirator, and to plan the sampling.

Good to know

Control the dust at the source before you count on a respirator: use water on the saw, a vacuum on the grinder and a shroud on the drill, and work upwind. Sample the air for each task and each worker, and do not rely on one value. Keep the records, and check the exposure again when the task, the material or the controls change. Remember that the real limit is the one of the standard that applies to your job.

The noise exposure calculator gives the dose of a worker exposed to noise, the OSHA incident rate calculator gives the rate of recordable injuries, the dust control water truck calculator gives the water needed to control the dust on a site and the concrete saw cut joint layout calculator gives the sawing time of a slab.

Frequently asked questions

What is the limit for respirable crystalline silica?

The OSHA standard for construction sets a permissible exposure limit of 50 µg/m³ of respirable crystalline silica as an 8-hour time-weighted average, and an action level of 25 µg/m³. When the exposure is at or above the action level, the employer must sample the air and monitor the workers. The limit is the same for quartz, cristobalite and tridymite, and it applies to the air that the worker breathes.

How is the TWA computed?

The 8-hour TWA is the sum, for all the periods of the shift, of the concentration times the duration, divided by 8 hours. Periods without exposure count for zero in the sum. A shift longer than 8 hours uses the same total divided by 8, as the standard does not change the divisor. The calculator takes up to three periods and adds the doses that the worker receives in each one.

What is the protection factor of a respirator?

The assigned protection factor, or APF, is the ratio between the concentration outside and inside the respirator that a user can expect with a good fit. A half-mask has an APF of 10, a loose-fitting powered respirator 25 and a full facepiece 50. The exposure inside the mask is the TWA divided by the APF. A respirator needs a fit test and a medical evaluation, and it does not replace the control of the dust at the source.

What are the limits of the calculator?

The calculator uses the concentrations that you enter, and it does not replace the air sampling that the standard requires. It assumes the same limit for all the forms of silica, it does not include the control of the dust by water or by vacuum, and it is not a substitute for an exposure control plan. Check the standard that applies in your place, and the lower limits that some employers or countries have.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.