Skip to content
Omnikalc

Slider-crank mechanism calculator

Enter the crank radius, the rod length, the crank angle and the speed to get the position, the velocity and the acceleration of the slider.

Updated on
Your inputs
mm

Value out of range

mm

Value out of range

°

Value out of range

rpm

Value out of range

Results

Slider displacement from top dead center

18.87 mm

Slider velocity
6.90 m/s
Slider acceleration (approximate)
872 m/s²
Acceleration in g
89.0 g
Mean slider speed
5.00 m/s
Rod ratio L ÷ R
3.00
Stroke
100.0 mm

The slider-crank calculator gives the displacement, the velocity and the acceleration of the slider for a crank angle, together with the mean speed, the rod ratio and the stroke of the mechanism.

How the calculation works

  • Enter the crank radius and the connecting rod length.
  • Enter the crank angle from top dead center and the crank speed.
  • The calculator solves the geometry of the rod and derives the velocity and the acceleration.

Example

With a crank of 50 mm and a rod of 150 mm, a rod ratio of 3.00 and a stroke of 100.0 mm, the slider at 45 ° and 1500 rpm is 18.87 mm below top dead center. It moves at 6.90 m/s and accelerates at 872 m/s², or 89.0 g. The mean speed over a cycle is 5.00 m/s.

Why it matters

The calculator helps engine designers, mechanical engineers, students and makers who work with pistons, compressors, pumps, presses and shapers, and who need the motion and the inertia loads of a slider driven by a crank.

Good to know

Measure the crank angle from the top dead center, where the slider is farthest from the crank axis. The sign of the velocity shows the direction: positive when the slider moves toward the crank axis in this calculator. The acceleration formula is a two-term approximation, accurate for rod ratios above about 3, and it is slightly off for short rods. For an engine, multiply the acceleration by the mass of the piston and the part of the rod that moves in a straight line to find the inertia force. For high speeds, balance the forces with counterweights or balance shafts.

The piston speed calculator gives the mean speed and the redline of an engine, the compression ratio calculator links the stroke to the compression, the flywheel energy calculator sizes the flywheel that smooths the motion and the horsepower torque calculator converts the power at the crank.

Frequently asked questions

How is the position of a piston calculated?

The distance from the crank axis to the slider is x = R × cos θ + √(L² − R² × sin² θ), with R the crank radius, L the rod length and θ the crank angle from top dead center. The displacement from top dead center is R + L − x. At 45 degrees with R = 50 mm and L = 150 mm, the slider is 18.9 mm from the top, while a pure sine motion would give 14.6 mm.

Why is the motion not a sine wave?

The rod tilts as the crank turns, which adds a second harmonic. The piston speeds up faster in the first half of the stroke and is slower near the bottom. The shorter the rod relative to the crank, the larger the distortion. With a rod ratio L / R of 3, the speed peak comes at about 74 degrees after top dead center instead of 90.

What is the acceleration of the slider?

The acceleration is about R × ω² × (cos θ + (R / L) × cos 2θ), a good approximation for rod ratios above 3. It is highest at top dead center, where it is R × ω² × (1 + R / L). At 1 500 rpm with a 50 mm crank and a 150 mm rod, it is 1 645 m/s², or 168 g.

How do the rod ratio and the speed affect the loads?

The inertia force of the piston is its mass times the acceleration, and it rises with the square of the speed. A longer rod lowers the second-harmonic term and reduces the side thrust on the cylinder wall. High-speed engines use a rod ratio of 1.6 to 1.9 for the stroke, balancing compactness and the side loads.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.