Skip to content
Omnikalc

Soil compaction calculator: did the fill reach the required density?

Enter the field wet unit weight and moisture with the Proctor maximum and optimum to get the relative compaction, saturation and air voids.

Updated on
Your inputs
pcf

Value out of range

%

Value out of range

pcf

Value out of range

%

Value out of range

Value out of range

Results

Relative compaction

96.3 %

Meets the common 95 % requirement for structural fill
Field dry unit weight
110.7 pcf
Degree of saturation
62.1 %
Air voids in the soil volume
13.0 %
Zero-air-voids dry unit weight at this moisture
127.3 pcf

A fill is only as good as its density, and the number to check is the relative compaction. The soil compaction calculator takes the field wet unit weight and moisture content, the Proctor maximum dry unit weight and optimum moisture, and the specific gravity of the soil, and gives the relative compaction, the field dry unit weight, the degree of saturation, the air voids and the zero-air-voids dry unit weight.

How the calculation works

  • Enter the wet unit weight and the moisture content measured in the field, for example by a sand cone or a nuclear gauge and an oven sample.
  • Enter the maximum dry unit weight and the optimum moisture content from the lab Proctor test on the same soil.
  • The field dry unit weight is wet unit weight ÷ (1 + moisture content). The relative compaction is this divided by the Proctor maximum.
  • With the specific gravity of the solids, the calculator finds the degree of saturation and the air voids. The zero-air-voids line is the highest dry weight possible at that moisture: Gs × γw ÷ (1 + w × Gs).

Example

A fill has a wet unit weight of 124 pcf and a moisture content of 12 %, so the dry unit weight is 124 ÷ 1.12 = 110.7 pcf. The Proctor test gave a maximum of 115 pcf at 13 %, so the relative compaction is 96.3 %, which passes a 95 % specification. With a specific gravity of 2.70, the void ratio is 0.522, the degree of saturation is 62.1 % and the air voids are 13.0 %. The zero-air-voids dry weight at 12 % moisture is 127.3 pcf, well above the field value, as it always must be.

Why it matters

Under-compacted fill settles, cracks slabs and fails under footings, and it is expensive to fix after the fact. Quick arithmetic on a test result tells the crew whether to roll again, change the moisture or accept the lift, and the saturation and air voids help find problems with the test itself.

Good to know

The calculation depends on correct field and lab tests, on the same soil and on a representative sample. Specifications differ by project, soil type and test method. Oversize particles also affect the comparison, and the lab maximum may need a correction. An inspector or engineer decides what is acceptable, and this tool helps with arithmetic.

The porosity and void ratio calculator covers phase relations, the retaining wall calculator deals with fill behind walls, the footing size calculator sizes a footing on compacted soil, and the concrete volume calculator covers the slab on top.

Frequently asked questions

What is relative compaction?

It is the dry unit weight of the compacted fill measured in the field, as a percentage of the maximum dry unit weight found in the lab Proctor test on the same soil. Specifications ask for 90 to 95 percent, or more under footings and roads, since a denser fill settles less and carries more load.

What is the Proctor test?

It is a lab test where soil at different moisture contents is compacted in a mould with a fixed energy. The dry unit weight peaks at the optimum moisture content, where water helps the grains slide into a tight packing. Standard and modified Proctor tests use different energies and give different maximums.

What is the zero-air-voids curve?

It is the dry unit weight the soil would have at each moisture content if all the air were driven out and the voids were full of water. No real compaction can exceed it, so a field value above the curve signals a measurement error. Well-compacted soils usually keep about 5 to 10 percent air voids.

Why do moisture and density go together?

Too dry, and friction between grains resists compaction. Too wet, and water fills the voids and cushions the blows, so density drops. Compacting at or slightly wet of the optimum gives a good density and, for clay, a more flexible fill. Checking the moisture is as important as checking the density.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.