Skip to content
Omnikalc

Soil nail pullout calculator: allowable pullout of a grouted nail against the tension it must carry

Enter the drill hole, the bond length, the bond stress, the safety factor, the cut height, the soil, the spacing and the bar to get the pullout capacity, the nail tension, the bar strength and the ratio of demand to capacity.

Updated on
Your inputs
in

Value out of range

ft

Value out of range

psi

Value out of range

Value out of range

ft

Value out of range

lb/ft³

Value out of range

Value out of range

ft

Value out of range

ft

Value out of range

Results

Demand over governing capacity

0.76

The nail has enough capacity
Ultimate pullout capacity
33.9 kips
Allowable pullout capacity
17.0 kips
Tension demand on a nail
12.9 kips
Allowable tension of the bar
26.1 kips

The soil nail pullout calculator compares the allowable pullout capacity of a grouted nail with the tension that it carries in an excavation, from the drill hole, the bond length, the bond stress and the earth pressure, with the strength of the bar.

How the calculation works

  • Enter the drill hole diameter, the bond length of the nail behind the failure surface and the ultimate bond stress of the grout in the soil, from a pullout test or the soil report.
  • Enter the safety factor, the height of the excavation, the unit weight and the coefficient Ka of the soil, and the spacing of the nails.
  • Choose the bar of the nail and its grade.
  • The calculator finds the ultimate and allowable pullout capacity, the tension that each nail must carry, the allowable tension of the bar and the ratio of the demand to the governing capacity.

Example

A nail has a 6 in drill hole, 15 ft of bond length and a bond stress of 10 psi. Its ultimate pullout is π × 6 × 180 × 10 / 1000 = 33.9 kips, and 17.0 kips with a safety factor of 2. For a 20 ft cut in soil of 120 lb/ft³ and Ka = 0.33, the pressure is 0.65 × 0.33 × 120 × 20 = 514.8 psf, and a nail at 5 ft by 5 ft carries 12.9 kips. A No. 8 bar of Grade 60 allows 0.55 × 60 × 0.79 = 26.1 kips, so the pullout governs and the ratio is 0.76.

Why it matters

The calculator helps geotechnical engineers, foundation contractors, excavation designers and students to size the length and the spacing of soil nails in a first design, to compare the pullout with the strength of the bar and to see the effect of the bond stress. It reproduces the first checks of the FHWA method for a nail.

Good to know

Use a bond stress from pullout tests on trial nails on the site, and not only from a table. Make the bond length at least the part of the nail behind the failure surface, and the total length about 0.7 to 1.0 times the height of the wall. Protect the bar against corrosion for a permanent wall and place drains behind the facing.

The ground anchor bond length calculator covers the prestressed anchors, the Rankine earth pressure calculator gives the lateral pressure, the retaining wall calculator checks a gravity wall and the soil unit weight calculator converts the density of the soil.

Frequently asked questions

What is a soil nail wall?

A soil nail wall is an excavation support made of steel bars, the nails, that are drilled and grouted into the soil as the excavation goes down, with a facing of shotcrete. The nails are passive: they take their load when the soil moves a little, and they reinforce the soil like the rebar in concrete. The system is quick and economical for cuts in firm soils and for the repair of slopes.

How is the pullout capacity found?

The nail resists by the friction, or bond, between the grout and the soil along the part of the nail behind the failure surface. The ultimate pullout is the bond stress multiplied by the area of the drill hole surface, π D L. The bond stress depends on the soil and on the method of drilling and grouting, and it is best found by pullout tests on trial nails. The allowable value is divided by a safety factor of about 2.

How is the tension in the nail estimated?

The calculator uses the apparent earth pressure diagram of the FHWA guidelines, with a maximum pressure of 0.65 Ka γ H, and assumes that each nail carries the pressure over the area that it serves, its horizontal spacing multiplied by its vertical spacing. The real tension varies with the depth of the nail and the stage of excavation, so a full design includes the global stability of the wall.

What are the limits of the calculator?

The calculator checks the pullout and the bar of a single nail. It does not check the global stability of the wall, the facing and the head of the nail, the corrosion protection, the nails at the top and the bottom rows, or the drainage behind the wall. The soil parameters must come from a geotechnical investigation, and a geotechnical engineer must design the wall.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.