Skip to content
Omnikalc

Spray nozzle flow calculator: how flow changes with pressure

Enter the rated flow and pressure of a nozzle, the operating pressure, the number of nozzles and a target flow to get the nozzle flow, the total flow, the exit velocity and the pressure needed for the target.

Updated on
Your inputs
gpm

Value out of range

psi

Value out of range

psi

Value out of range

Value out of range

gpm

Value out of range

lb/ft³

Value out of range

Results

Flow rate of one nozzle at the operating pressure

2.83 gpm

Total flow rate of all the nozzles
56.57 gpm
Change of the nozzle flow from its rating
41.4 %
Ideal exit velocity
109.0 ft/s
Pressure needed for the target flow
78.4 psi
Total flow over the target flow
101.0 %
Total flow within 5% of the target

The spray nozzle flow and pressure calculator applies the square-root law to give the flow of a nozzle at an operating pressure, the total flow of a set of nozzles, the ideal exit velocity and the pressure needed for a target flow.

How the calculation works

  • Enter the rated flow of one nozzle and the pressure at which it is rated (from the nozzle data sheet), and the number of nozzles.
  • Enter the operating pressure and the target total flow of the spray system, with the density of the liquid.
  • The calculator applies the square-root law Q2 = Q1 √(P2 / P1) to the nozzle flow, and multiplies it by the number of nozzles.
  • It also gives the ideal exit velocity √(2 P / ρ) and the pressure needed to reach the target flow: P = P1 × (Qtarget / Q1)².

Example

A nozzle is rated at 2 gpm at 40 psi, and 20 nozzles run at 80 psi. The flow of one nozzle is 2 × √(80 / 40) = 2.83 gpm, which is 41.4% above the rating, and the total flow is 56.57 gpm. The ideal exit velocity is √(2 × 80 × 144 × 32.174 / 62.4) = 109.0 ft/s. For a target of 56 gpm, the pressure needed is 40 × (56 / 40)² = 78.4 psi, and the system gives 101.0% of the target.

Why it matters

The calculator helps farmers and sprayer operators, washdown and fire protection designers, cooling and humidification engineers, and students to adjust the pressure of a spray system, to check the application rate and to select the right nozzle size. It saves reading the nozzle chart for each pressure.

Good to know

Use the rated flow and pressure of the data sheet of the exact nozzle. Stay inside the pressure range of the nozzle for a good spray pattern. Check the nozzles for wear and replace them when the flow rises by 10%. Measure the real flow by collecting the discharge in a container during a minute.

The orifice flow calculator covers the flow through an orifice, the pump power calculator sizes the pump, the Bernoulli calculator covers pressure and velocity and the Reynolds number calculator checks the flow regime.

Frequently asked questions

How does the flow of a nozzle depend on pressure?

The flow through a nozzle varies with the square root of the pressure drop: doubling the pressure raises the flow by only 41%. To double the flow, the pressure must be multiplied by four. This comes from the Bernoulli equation, with a nearly constant discharge coefficient. The law is accurate to about ±5% for common spray nozzles within their rated pressure range.

What is the exit velocity?

The ideal velocity of the liquid at the nozzle orifice is √(2 ΔP / ρ), from the Bernoulli equation. The real velocity is a little lower, by the discharge coefficient of 0.6 to 0.95 according to the nozzle. The velocity matters for the spray impact, the throw distance and the drop size. A higher pressure gives a finer spray and a higher impact, but also a higher flow.

How do I size the pressure for a target flow?

Divide the target flow by the number of nozzles and compare it with the rated flow of one nozzle. The pressure needed is the rated pressure times the square of that ratio. Choose a nozzle size so that the operating pressure falls in the range given by the maker, which is often 20 to 100 psi (1.5 to 7 bar) for agricultural and cleaning nozzles.

What affects the real flow of a nozzle?

Wear enlarges the orifice and raises the flow, especially with abrasive liquids, while clogging reduces it. The viscosity and the temperature of the liquid change the flow slightly from the water rating. For a liquid of a different density, the flow in volume varies with 1 over the square root of the density, so the rating on water must be corrected for specific gravity.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.