Skip to content
Omnikalc

How much flows through an orifice or nozzle?

Enter the orifice diameter, the pressure drop, the discharge coefficient and the fluid density to get the flow rate and the jet speed.

Updated on
Your inputs

Value out of range

Value out of range

kg/m³

Value out of range

Results

Flow rate (US gal/min)

28.8 gal/min

This is the flow in an ideal clean orifice: real systems with long pipes or dirty fluids will flow less
Flow rate (L/s)
1.81 L/s
Flow rate (m³/h)
6.53 m³/h
Ideal jet speed (ft/s)
77.1 ft/s
Ideal jet speed (m/s)
23.5 m/s

How much water comes out of a hole in a tank, a spray nozzle, a sprinkler head or a drilled plate in a pipe? The orifice equation, derived from Bernoulli’s principle, answers it from three things: the size of the opening, the pressure drop across it, and the density of the fluid. This calculator also takes the discharge coefficient into account, which depends on the shape of the opening.

How the calculation works

  • Area A = π × d² ÷ 4
  • Ideal jet speed v = √(2 × ΔP ÷ ρ)
  • Flow rate Q = Cd × A × v

Pressure in kPa is converted to pascals (× 1,000) and diameters in millimeters to meters. The discharge coefficient Cd is 0.61 for a sharp-edged hole, 0.82 for a short tube and about 0.97 for a smooth rounded nozzle.

Example

A ½ inch (12.7 mm) sharp-edged orifice with a 40 psi (276 kPa) pressure drop passes water. The area is 1.27 × 10⁻⁴ m², the ideal jet speed is √(2 × 275,800 ÷ 1,000) = 23.5 m/s (77 ft/s), and the flow is 0.61 × 1.27 × 10⁻⁴ × 23.5 = 1.8 × 10⁻³ m³/s, or 1.8 L/s (about 28.8 gal/min).

Why it matters

The orifice equation sizes nozzles, spray bars, relief openings, flow restrictors and leaks. It also explains why flow rises with the square root of pressure: doubling the pressure does not double the flow, it increases it by only 41 %. And because the area grows with the square of the diameter, a hole twice as wide passes four times as much.

Good to know

The equation assumes a clean, incompressible liquid, a thin plate and a turbulent flow. Viscous liquids such as oil at low temperature have a lower coefficient. Long pipes upstream or downstream add friction losses that reduce the real flow, and an orifice discharging under water has a smaller pressure drop than one discharging to air. For gas, high pressure drops or flow measurement, use standards such as ISO 5167. This tool is for education.

The tank drain time calculator applies the same law to a falling water level, the pipe flow velocity calculator gives the speed in a pipe, and the weir flow calculator estimates flow over an open channel.

Frequently asked questions

What is the orifice flow equation?

Q = Cd × A × √(2 × ΔP ÷ ρ), where A is the area of the opening, ΔP the pressure drop across it, ρ the density of the fluid and Cd the discharge coefficient. It comes from Bernoulli's equation.

What is the discharge coefficient?

It accounts for the narrowing of the jet just after the opening (the vena contracta) and for friction. A sharp-edged hole has a value near 0.61; a short tube is about 0.82; a smooth rounded nozzle is close to 0.97 or higher.

Does the formula work for gas?

Only at low pressure drops, when the gas density barely changes. At high pressure drops, gas flow becomes compressible, and may even choke at sonic speed, so another equation applies.

How do I convert head to pressure?

A column of water exerts a pressure of about 9.81 kPa for each meter of height (0.433 psi per foot). To use head directly, multiply by 9.81 kPa for water, and by density ratio for other fluids.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.