Skip to content
Omnikalc

Surface finish calculator: what feed gives the roughness you need?

Enter the feed per revolution, the tool nose radius and the target Ra to get the theoretical roughness and the feed needed for the target.

Updated on
Your inputs
in/rev

Value out of range

in

Value out of range

µin

Value out of range

Results

Theoretical surface roughness Ra

64.00 µin

Typical machined finish (up to 125 µin)
Theoretical peak-to-valley height Rt
256.00 µin
Feed needed for the target Ra
0.0057 in/rev
Ra as a multiple of the target
2.00
Ra in micrometres
1.63 µm

When a drawing asks for a surface roughness, the feed and the tool nose radius decide whether a turning pass can meet it. The surface finish calculator takes the feed per revolution, the nose radius and the target Ra, and gives the theoretical Ra, the peak-to-valley height Rt, the feed needed for the target, the ratio to the target and the roughness in micrometres.

How the calculation works

  • Enter the feed per revolution of the turning operation and the nose radius of the insert. These two numbers set the shape of the ridges left on the part.
  • Enter the target roughness Ra from the drawing, in microinches.
  • The ideal ridges give a theoretical Ra = f² ÷ (32 × r) and a peak-to-valley height Rt = f² ÷ (8 × r), with f the feed and r the nose radius.
  • To reach a target, the feed needed is √(32 × r × Ra). Halving the feed cuts the roughness to a quarter, and doubling the nose radius halves it.

Example

An insert with a 1/32 inch nose radius (0.03125 in) turns at a feed of 0.008 in/rev. The theoretical roughness is 0.008² ÷ (32 × 0.03125) = 64 µin (1.63 µm), and the peak-to-valley height is 256 µin. A drawing that asks for 32 µin needs a feed of √(32 × 0.03125 × 0.000032) = 0.0057 in/rev, about 29 percent lower. The finish is 2.0 times the target at the current feed.

Why it matters

Choosing the feed from the geometry avoids trial passes on expensive parts. The calculator shows the trade-off between productivity, since a bigger feed removes metal faster, and finish, which falls with the square of the feed, and it shows what a larger nose radius buys.

Good to know

The result is a geometric minimum for an ideal tool and a rigid setup. Real roughness is usually higher. The formula holds when the feed is smaller than twice the nose radius and the depth of cut is larger than the radius. For milling, grinding and other processes, other relationships apply. Check the first part with a roughness gauge.

The cutting speed calculator sets the spindle speed, the taper angle calculator covers conical features, the bend allowance calculator helps with sheet metal, and the welding heat input calculator covers another process parameter.

Frequently asked questions

What is Ra?

Ra is the arithmetic mean roughness: the average height of the peaks and valleys of a surface from its mean line, over a sampling length. It is the most common roughness value on drawings, given in microinches in the United States and in micrometres elsewhere. A lower Ra means a smoother surface.

How is the formula derived?

A round-nosed tool moving along the part leaves a series of circular arcs. For a small feed compared with the nose radius, the arcs are almost parabolas with a depth of f² ÷ (8r) from peak to valley. The average height from the mean line is a quarter of that, which gives f² ÷ (32r) for Ra.

Why is the real finish worse?

The formula gives the best possible finish from the tool shape. In practice, tool wear, vibration, built-up edge, machine rigidity, cutting speed and the material all raise the roughness, often by a factor of 1.5 to 3. A sharp tool at a good speed on a rigid machine comes closest to the ideal.

What are typical Ra values?

Rough turning gives 125 to 250 µin (3.2 to 6.3 µm). A normal finishing cut gives 32 to 63 µin (0.8 to 1.6 µm). Ground surfaces are 8 to 32 µin and lapped ones are below 8 µin. Choose the roughness that the function needs, since finer finishes cost more time and money.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.