Skip to content
Omnikalc

Thick-wall cylinder calculator: stress in a high-pressure cylinder

Enter the pressure, the radii and the yield strength of a thick cylinder to get the Lamé hoop stress at the inner and outer surfaces, the Tresca stress, the safety factor and the error of the thin-wall formula.

Updated on
Your inputs
psi

Value out of range

in

Value out of range

in

Value out of range

psi

Value out of range

psi

Value out of range

Results

Safety factor against yielding (Tresca)

1.67

Adequate margin against yielding
Hoop stress at the inner surface (Lamé)
26,000 psi
Hoop stress at the outer surface (Lamé)
16,000 psi
Tresca stress at the inner surface (σθ − σr)
36,000 psi
Thin-wall estimate of the hoop stress p r / t
20,000 psi
Error of the thin-wall formula
23.1 %

In a thick-wall cylinder, the stress is not uniform across the wall and it peaks at the bore. The thick-wall cylinder calculator applies the Lamé equations to give the hoop stress at the inner and outer surfaces, the Tresca stress, a safety factor and the error of the thin-wall formula.

How the calculation works

  • Enter the internal pressure, the inner radius and the outer radius of the cylinder, and the external pressure if there is one (zero for a cylinder in air).
  • Enter the yield strength of the material to get a safety factor.
  • The calculator applies the Lamé equations for a thick cylinder: σθ = [pi ri² − po ro² + (pi − po) ri² ro² / r²] / (ro² − ri²), evaluated at the inner and the outer surfaces. The radial stress at the bore is −pi.
  • It compares the result with the thin-wall formula p r / t, which is only accurate for a thin wall, and it gives the Tresca stress σθ − σr for the safety factor.

Example

A steel cylinder has an inner radius of 2 in, an outer radius of 3 in, an internal pressure of 10,000 psi and no external pressure. The hoop stress at the bore is 10,000 × (4 + 9) / (9 − 4) = 26,000 psi, and 16,000 psi at the outer surface. The Tresca stress at the bore is 26,000 + 10,000 = 36,000 psi, so with a yield strength of 60,000 psi the safety factor is 1.67. The thin-wall formula gives 10,000 × 2 / 1 = 20,000 psi, which is 23.1% too low.

Why it matters

The calculator helps mechanical engineers, designers of hydraulic cylinders, high-pressure lines and presses, and students to check a thick cylinder, to see when the thin-wall formula stops being valid and to compare a wall thickness with the pressure. It shows how little a thicker wall helps when the ratio of the radii is already large.

Good to know

Use the thin-wall formula only if the thickness is less than a tenth of the radius. Add a margin for the pressure peaks and the fatigue. Check that the material keeps its strength at the working temperature. For a very high pressure, consider an autofrettage or a shrink fit, which put a compression at the bore.

The pressure vessel stress calculator covers thin shells, the pipe wall thickness calculator sizes pipes by code, the principal stress calculator combines stress components and the interference fit calculator gives the pressure of a shrink fit.

Frequently asked questions

When is a cylinder thick-walled?

A cylinder is usually called thin-walled if the wall thickness is less than about one tenth of the inner radius. In that case the hoop stress is almost uniform across the wall and the formula p r / t is accurate within a few percent. For a thicker wall, the stress varies strongly across the wall and is highest at the bore, so the Lamé equations are needed. High-pressure hydraulic cylinders, gun barrels and autoclaves are thick-walled.

What are the Lamé equations?

For a long cylinder under internal and external pressure, the elasticity solution gives the hoop and radial stresses at a radius r as σθ = A + B / r² and σr = A − B / r², where A and B depend on the pressures and the radii. The hoop stress is always greater at the inner surface, and it is a tension under internal pressure. The radial stress is a compression equal to the pressure at each surface.

Why use the Tresca stress?

At the bore the hoop stress is a tension and the radial stress is a compression, so the material is under a high shear. The maximum shear stress theory of Tresca says that yielding starts when σθ − σr reaches the yield strength. The von Mises theory gives a result about 13% higher for the strength. This calculator uses the Tresca theory, which is conservative.

What are the limits of the formulas?

They assume a long cylinder, a constant pressure, a linear elastic material and no axial constraint. They do not include the thermal stresses, the stress concentration at cross-holes and at the ends, the fatigue under cycling pressure or the plastic behavior. Pressure equipment is governed by codes such as the ASME Boiler and Pressure Vessel Code, which set the allowable stress and the design rules.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.