Skip to content
Omnikalc

Lifting lug and padeye capacity calculator

Enter the load, the design factor, the sling angle, the plate and the hole to get the load on a lug, the net section, tear-out and bearing strengths and the ratio.

Updated on
Your inputs
lb

Value out of range

Value out of range

Value out of range

°

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

ksi

Value out of range

ksi

Value out of range

Results

Demand to capacity ratio

0.87

The lug has a margin on the three checks
Design load on one lug
23,094 lb
Net section tension strength
69,668 lb
Tear-out strength
41,801 lb
Pin bearing strength
26,578 lb

The lifting lug calculator gives the load on one lug, the net section tension, tear-out and pin bearing strengths of a padeye and the demand to capacity ratio, from the weight, the design factor, the sling angle and the plate geometry.

How the calculation works

  • Enter the weight lifted, the design factor, the number of lugs and the sling angle.
  • Enter the plate thickness, the pin and hole diameters, the edge distance and the width at the hole, with Fy and Fu.
  • The calculator gives the load on a lug, the three strengths and the demand to capacity ratio.

Example

A load of 20,000 lb is lifted with 2 lugs, slings at 60 degrees and a design factor of 2.0. The load on one lug is 2 × 20,000 / (2 × sin 60°) = 23,094 lb. For a plate of 5/8 in with a 7/8 in pin in a 15/16 in hole, an edge distance of 1.75 in and a width of 3.5 in in A36 steel, the net section tension strength is 69,668 lb, the tear-out strength is 41,801 lb and the pin bearing strength is 26,578 lb. The ratio is 23,094 / 26,578 = 0.87.

Why it matters

The calculator helps riggers, structural engineers, steel fabricators and crane planners to size or check the thickness and the geometry of a welded lifting lug, and to see which of the three limits governs.

Good to know

Keep the pin diameter close to the hole diameter, not less than 90 to 95 % of it, since a loose pin raises the bearing stress. Put the lug in the plane of the sling, and add cheek plates if the plate is thin. Weld the lug with a full penetration or a fillet weld sized for the load and the design factor, and inspect the weld. Mark the lug with the rated load, and have the plan checked by a qualified person.

The sling angle calculator gives the tension in each leg of a lift, the two-point lift calculator gives the load and the tension for an off-center load, the clevis pin shear calculator checks a pin and the fillet weld strength calculator checks the weld of the lug.

Frequently asked questions

What does the calculator check?

The calculator checks the three failure modes of the plate around the hole: tension through the net section at the hole, tear-out of the metal between the hole and the edge in the direction of the load, and bearing of the pin on the hole. The strength is the smallest of the three. It uses the AISC resistance factor of 0.75 and the bearing limit of 1.8 Fy Apb. It does not check the weld of the lug to the load, which often governs.

What is the design factor?

The design factor multiplies the working load to cover the dynamic effects of the lift and the uncertainty. A factor of 2.0 is common for the lugs of a lift with a service factor, and the standards for below the hook lifting devices, such as ASME BTH-1, give design factors of 2.00 to 2.50 or more, depending on the design category. Use the factor of the standard or the rigging plan, and not the default.

How does the sling angle change the load?

The tension in a sling is the load shared by the lug, divided by the sine of the angle from the horizontal. A sling at 60 degrees carries 15 % more than the vertical share and a sling at 30 degrees carries twice as much. The calculator uses this vertical sharing between the lugs and assumes the load is in the plane of the plate. A side load can bend the plate and must be avoided or checked.

What does the calculator leave out?

The calculator does not check the weld between the lug and the beam or the plate, the local bending of the base, the shackle or the pin, the hook-up of the load and the fatigue of repeated lifts. Do not use the result alone for a lift over people or for a critical lift. A qualified engineer must design and approve the lugs, and the lugs must be tested or inspected as the standard asks.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.