Skip to content
Omnikalc

Tolerance stack-up calculator: will your parts still fit together?

Enter the lengths and tolerances of a housing and three stacked parts to get the nominal gap, the worst-case and RSS tolerances and the chance of interference.

Updated on
Your inputs
in

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

Results

Smallest gap, worst case

-0.0030

The parts can interfere in the worst case
Nominal gap
0.015
Worst-case tolerance on the gap (±)
0.0180
Statistical (RSS) tolerance on the gap (±)
0.0091
Smallest gap, RSS
0.0059
Chance of interference (parts per million)
0.336

When parts stack up in an assembly, their small errors add together, and the gap left at the end can vanish. The tolerance stack-up calculator takes the housing length and the three parts inside it, each with its tolerance, and gives the nominal gap, the worst-case tolerance, the statistical RSS tolerance, the smallest gap in both methods and the chance of interference.

How the calculation works

  • Enter the nominal length of the housing (the part that sets the total) and its tolerance, then the three parts that stack inside it, each with its tolerance.
  • The nominal gap is the housing length minus the three parts: A − B − C − D.
  • The worst-case tolerance is the plain sum of the four tolerances. The statistical (RSS) tolerance is the square root of the sum of their squares.
  • Compare the smallest gap in each method. A negative worst-case gap means that the parts can interfere. The chance of interference assumes that each tolerance is three standard deviations of a normal distribution.

Example

A housing of 2.000 ± 0.005 in holds three parts of 0.500 ± 0.004, 0.750 ± 0.005 and 0.735 ± 0.004 in. The nominal gap is 0.015 in. The worst-case tolerance is 0.005 + 0.004 + 0.005 + 0.004 = ±0.018, so the smallest gap is −0.003 in and the parts can interfere. The RSS tolerance is √(0.005² + 0.004² + 0.005² + 0.004²) = ±0.00906, giving a smallest gap of +0.00594 in. With normal distributions, the chance of interference is about 0.34 parts per million.

Why it matters

Tolerances drive cost: tighter ones need better machines and more inspection. A stack-up shows which dimensions decide whether the assembly works and where you can relax a tolerance without risk. It also shows how much you gain by accepting a tiny chance of interference instead of requiring a fit every time.

Good to know

This is a one-dimensional stack with a housing and three parts, where every dimension adds or subtracts along a single line. Real assemblies have angles, geometric tolerances, thermal growth, wear and fits that need a 3D analysis. The statistical figures assume centred, normal and independent dimensions. Check critical gaps against the drawings and the standards of your industry.

The thermal expansion calculator shows how lengths change with temperature, the bolt circle calculator finds hole positions, the compression spring calculator sizes springs that sit in a stack, and the shaft torsion calculator checks twisted shafts.

Frequently asked questions

What is a tolerance stack-up?

It is the way the tolerances of several parts add up in an assembly. Each part can be a little too long or too short, and the gap that remains between them is the housing length minus the part lengths, so the errors combine. A tolerance analysis tells you whether the gap will always be positive, or only most of the time.

What is the difference between worst-case and RSS?

The worst-case method adds the tolerances directly, as if every part were at its limit in the worst direction at the same time. It guarantees a fit but is expensive. The root-sum-square method assumes that the errors are random and independent, so they partly cancel, and the combined tolerance is the square root of the sum of squares.

When is the statistical method acceptable?

When the parts come from capable processes, are close to normally distributed and are picked at random for each assembly, and when a rare out-of-tolerance assembly can be accepted or reworked. For safety-critical gaps or small production runs, use the worst-case method. A stack of more parts gains more from the statistical approach.

What is the chance of interference?

The calculator takes each tolerance as three standard deviations of a normal distribution, so the combined standard deviation is the RSS tolerance divided by three. It then computes the probability that the gap is below zero, in parts per million. Real processes can be off centre or skewed, so the figure is an estimate.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.