Skip to content
Omnikalc

Tower crane load moment calculator: utilization and capacity at the lift radius

Enter the load, the radius, the rated load moment and the maximum capacity of the crane to get the load moment, the utilization, the capacity at the radius and the margin.

Updated on
Your inputs
tons

Value out of range

ft

Value out of range

ton-ft

Value out of range

tons

Value out of range

Results

Utilization of the rated moment

60.0 %

The lift is well within the rated moment
Load moment of the lift
480.0 ton-ft
Capacity at this radius
6.67 tons
Margin on the load
2.67 tons

The tower crane load moment calculator gives the load moment, the utilization of the rated moment, the capacity at the radius and the margin on the load for a lift, from the weight of the load, its radius and the rating of the crane.

How the calculation works

  • Enter the load with the hook block and the rigging, and the radius of the lift measured from the center of the tower.
  • Enter the rated load moment and the maximum rated capacity of the crane from its capacity chart.
  • The calculator finds the load moment, the utilization of the rated moment, the capacity at this radius and the margin on the load.

Example

A tower crane lifts 4 tons at a radius of 120 ft, so the load moment is 4 × 120 = 480.0 ton-ft. The crane has a rated moment of 800 ton-ft and a maximum capacity of 8 tons, so the utilization is 480 / 800 = 60.0 %. At 120 ft the crane can lift 800 / 120 = 6.67 tons, which is less than 8 tons, so the capacity at this radius is 6.67 tons and the margin on the load is 2.67 tons.

Why it matters

The calculator helps site managers, crane supervisors, lift planners and students to check quickly if a lift is within the rating of a tower crane, to see how the capacity falls when the radius grows, and to decide whether a load must be lifted closer to the tower or split in two.

Good to know

Always check the lift against the load chart of the manufacturer for the real jib length and configuration, and keep a margin of safety, because a load close to the rated moment leaves no room for the wind or the swing. Weigh the load, including the slings and the hook block, and keep the load as close to the tower as the site allows. Never exceed the rated moment, and stop the lift if the limiter alarm sounds.

The crane lift utilization and wind calculator adds the effect of the wind, the crane mat bearing pressure calculator checks the ground under the base, the sling angle calculator gives the tension in the slings and the wind load calculator gives the pressure of the wind on a surface.

Frequently asked questions

What is the load moment of a tower crane?

The load moment is the weight of the load times its radius from the axis of the tower, in ton-feet or ton-meters. A tower crane is limited by two things: the maximum load that its structure and its hoist can carry near the tower, and the load moment that its counterweight and its tower can resist. Close to the tower, the maximum load rules, and far from the tower, the load moment rules.

How do I find the capacity at a radius?

The capacity at a radius is the smaller of the maximum rated capacity and the rated load moment divided by the radius. In the example, the rated moment of 800 ton-ft divided by 120 ft gives 6.67 tons, which is less than the maximum of 8 tons, so the moment rules. The calculator uses this simple relation, which is close to the real chart in the range where the moment rules.

What must be included in the load?

The load must include everything that hangs from the jib: the payload, the slings, the spreader, the hook block and the weight of the hoist rope if the manufacturer says so. A loaded bucket, a form panel with its water or its snow, or a load that sticks to the ground can weigh more than expected. A safety factor and a check of the weight of the load before the lift are good practice.

What are the limits of the calculator?

The calculator checks the load moment against a rated value. It does not replace the load chart of the manufacturer, which depends on the jib length, the counterweight, the number of falls and the configuration. It does not include the wind, the dynamic effect of the lift, the slope of the base, the second crane in the area or the tipping of the tower. The lift plan must be approved by a qualified person.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.