Skip to content
Omnikalc

Crane runway beam moment under moving wheels calculator

Enter the wheel load, the wheel spacing, the span, the impact, the beam weight, the section modulus and the moment of inertia to get the moment, the ratio and the deflection.

Updated on
Your inputs
kip

Value out of range

ft

Value out of range

ft

Value out of range

%

Value out of range

kip/ft

Value out of range

in³

Value out of range

in⁴

Value out of range

ksi

Value out of range

Results

Ratio of the moment to the allowable

0.54

The runway beam can carry the moment
Wheel load with impact
10.0 kip
Moment from the wheels
112.7 kip-ft
Moment from the beam weight
7.9 kip-ft
Total moment
120.5 kip-ft
Allowable moment
225.0 kip-ft
Deflection under the wheels
0.49 in
Ratio of the deflection to L/600
0.81
The deflection is within L/600

The crane runway beam moment under moving wheels calculator gives the wheel load with impact, the moment from the wheels, the total moment, the allowable moment, the ratio and the deflection of a simply supported runway beam with two crane wheels, from the wheel load, the spacing and the span.

How the calculation works

  • Enter the maximum wheel load, the distance between the wheels, the span and the impact allowance.
  • Enter the weight of the beam, its section modulus, its moment of inertia and the yield strength.
  • The calculator finds the moments, the allowable moment, the ratios and the deflection.

Example

A crane with 8 kip per wheel and 25 % of impact loads 10.0 kip per wheel. For wheels 8 ft apart on a span of 30 ft, the moment of the wheels is 10 / (2 × 30) × (30 − 4)² = 112.7 kip-ft, and the beam weight adds 7.9 kip-ft, for 120.5 kip-ft. With 90 in³ and 50 ksi, the allowable moment is 225.0 kip-ft, so the ratio is 0.54. The deflection is 0.49 in, a ratio of 0.81 to L/600.

Why it matters

The calculator helps structural engineers, plant managers, crane installers and students to check a runway beam for a bridge crane, to see how the span and the wheel spacing change the moment, and to compare several sections before the detailed design.

Good to know

Use the real maximum wheel load of the manufacturer of the crane, with the trolley at the end of the bridge. Keep the runway rails straight and level within the tolerance of the crane, and check the alignment after the installation. Inspect the beam, the rail clips and the stops regularly, and do not use a crane on a beam that was designed for a smaller one.

The tower crane calculator checks the load moment of a lift, the beam deflection calculator gives the deflection for other loads, the steel beam lateral-torsional buckling calculator checks a beam without lateral support and the web shear buckling calculator checks a plate girder web.

Frequently asked questions

What is a crane runway beam?

A crane runway beam is a beam which carries the rail of an overhead bridge crane, in a workshop or a warehouse. The wheels of the crane run on it and give moving point loads. The beam is subjected to the vertical loads of the lift and of the crane, to the side forces of the trolley and of the bridge, and to the longitudinal forces of the braking of the crane.

Where is the maximum moment?

For two equal wheel loads on a simple span, the maximum moment is under one of the wheels, when the wheel is at a distance of a quarter of the wheel spacing from the midspan. It is the load divided by two times the span, times the square of the span minus half the wheel spacing. This formula is valid when the wheel spacing is less than 0.586 times the span.

Why is there an impact allowance?

The motion of the crane and of the load gives dynamic effects on the beam, so the standards add an impact allowance to the vertical wheel loads. It is 10 % for a pendant-operated crane and 25 % for a cab-operated or a radio-operated one in the AISC. The calculator applies the allowance to the wheel loads, and not to the weight of the beam.

What are the limits of the calculator?

The calculator checks the bending moment and the deflection of a simple span with two wheels. It does not check the side loads, the torsion, the lateral-torsional buckling of the top flange, the local stresses of the web under the wheel, the fatigue of the beam, the rail or the connections. A crane runway must be designed according to the standard for crane runways and with the data of the crane manufacturer.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.