Skip to content
Omnikalc

Vs30 calculator: what is the seismic site class of your soil profile?

Enter the thickness and shear wave velocity of the soil layers to get Vs30, the site class from A to E, the soil column period and the shear modulus.

Updated on
Your inputs
m

Value out of range

m/s

Value out of range

m

Value out of range

m/s

Value out of range

m

Value out of range

m/s

Value out of range

m

Value out of range

m/s

Value out of range

kg/m³

Value out of range

Results

Average shear wave velocity (Vs30)

311.7 m/s

Site class (1 = A, 2 = B, 3 = C, 4 = D, 5 = E)
4
Class D: stiff soil
Total thickness of the profile
30.0 m
Fundamental period of the soil column (4H ÷ Vs)
0.385 s
Small-strain shear modulus (ρ · Vs²)
184.6 MPa

The shaking at a site during an earthquake depends strongly on how stiff the top layers of soil are. The Vs30 calculator takes the thickness and shear wave velocity of up to four layers and a soil density, and gives the average shear wave velocity, the site class from A to E, the total thickness, the fundamental period of the soil column and the small-strain shear modulus.

How the calculation works

  • Enter the thickness and the shear wave velocity of up to four soil layers, from the surface down. Set a thickness to zero for unused layers.
  • The layers should add up to 30 m, the standard depth for site classification. If they do not, the calculator uses the profile you give.
  • The average shear wave velocity is the travel-time average: total thickness ÷ Σ (thickness ÷ velocity).
  • The calculator gives the site class from A to E, the period of the soil column and the small-strain shear modulus for the density you enter.

Example

A profile has 5 m at 180 m/s, 10 m at 260 m/s, 8 m at 400 m/s and 7 m at 700 m/s, a total of 30 m. The travel time through the layers is 5 ÷ 180 + 10 ÷ 260 + 8 ÷ 400 + 7 ÷ 700 = 0.0962 s, so Vs30 is 30 ÷ 0.0962 = 311.7 m/s, a Class D (stiff soil) site. The column period is 4 × 30 ÷ 311.7 = 0.385 s and the shear modulus with a density of 1,900 kg/m³ is 184.6 MPa.

Why it matters

The site class feeds the seismic design coefficients of a building. A change from class C to D or E can raise the design forces noticeably, so checking the classification early helps to anticipate the cost of the structure and the need for a geotechnical investigation.

Good to know

The class thresholds are those of ASCE 7 and the IBC based on Vs30, and other codes differ. The classification of a real site also depends on other criteria, such as liquefiable or sensitive soils, which need an engineer. The calculator is for learning and preliminary checks and does not replace a geotechnical report.

The earthquake magnitude calculator relates magnitude to energy, the footing size calculator sizes foundations, and the Poisson’s ratio calculator relates elastic constants of the ground.

Frequently asked questions

What is Vs30?

Vs30 is the time-averaged shear wave velocity in the top 30 metres of the ground. Because it is correlated with how much the ground shakes in an earthquake, building codes use it to classify sites and to choose the design ground motion. It is a travel-time average, so slow layers weigh more than fast ones.

What are the site classes?

In the ASCE 7 and IBC system, Class A is hard rock (Vs30 above 1,500 m/s), B is rock (760 to 1,500), C is very dense soil and soft rock (360 to 760), D is stiff soil (180 to 360) and E is soft clay soil (below 180). Class F covers soils that need a site-specific study, such as liquefiable soils. Other codes use similar classes with their own limits.

Why a travel-time average and not an ordinary average?

A wave spends more time in slow layers, so a thin soft layer has a large effect on the travel time and on how the site amplifies shaking. The harmonic-type average, total thickness divided by total travel time, reflects this, while an arithmetic average of velocities would overstate the stiffness.

Where do shear wave velocities come from?

They are measured in the field, for example with a downhole or crosshole test, a seismic CPT or surface-wave methods such as MASW, or estimated from other tests such as SPT blow counts through correlations. Correlations carry large uncertainty, so measured values are better for design.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.