Skip to content
Omnikalc

Wire drawing force calculator: pull needed to draw a wire through a die

Enter the diameters of the wire before and after the die, the flow stress of the metal, the half-angle of the die and the friction coefficient to get the reduction, the true strain, the drawing stress, the drawing force and the safety against breaking.

Updated on
Your inputs
in

Value out of range

in

Value out of range

ksi

Value out of range

°

Value out of range

Value out of range

Results

Drawing force

885 lb

Reduction of area
19.0 %
True strain ε = 2 ln(d0 / df)
0.211
Drawing stress
22.3 ksi
Drawing stress as a share of the flow stress
37.1 %
Safe reduction: the wire does not break in the die

In wire drawing, a wire is pulled through a die that reduces its diameter. The wire drawing force calculator gives the reduction of area, the true strain, the drawing stress with the effect of the friction and the die angle, and the drawing force, with the safety against breaking.

How the calculation works

  • Enter the initial and final diameters of the wire for one pass, and the mean flow stress of the metal over the deformation, about the average of the yield strength before and after the pass.
  • Enter the half-angle of the die, typically 4 to 8 degrees, and the friction coefficient, 0.05 to 0.10 with a good lubricant.
  • The calculator computes the reduction of area, the true strain ε = ln(A0 / Af) and the drawing stress σd = σ̄ ε (1 + μ cot α), which adds the effect of the friction in the die to the ideal work of deformation.
  • It gives the drawing force F = σd × Af and the ratio of the drawing stress to the flow stress, which must stay below 1 or the wire breaks.

Example

A wire is drawn from 0.250 in to 0.225 in in a die with a half-angle of 6° and a friction coefficient of 0.08, for a mean flow stress of 60 ksi. The reduction of area is 19.0% and the true strain is 2 × ln(0.250 / 0.225) = 0.211. The drawing stress is 60 × 0.211 × (1 + 0.08 / tan 6°) = 22.3 ksi. The drawing force is 22,267 psi × 0.0398 in² = 885 lb. The drawing stress is 37.1% of the flow stress, a safe pass.

Why it matters

The calculator helps wire and cable makers, metal forming engineers, jewelers and students to estimate the pull in a drawing pass, to check that the wire does not break and to see the effect of the die angle and the lubrication. It is also a good example of the forming of metals by plastic deformation.

Good to know

Keep the reduction per pass in the range of 15% to 30% for most metals. Use a die half-angle of 4 to 8 degrees, which balances the friction and the redundant work. Lubricate well, since the friction coefficient strongly changes the force. Anneal the wire if it hardens too much to be drawn further.

The true stress and strain calculator explains the logarithmic strain, the Young’s modulus calculator covers the elastic properties, the Larson-Miller calculator covers high-temperature creep and the hydraulic press calculator sizes a pull cylinder.

Frequently asked questions

What is the drawing stress?

In wire drawing, a wire is pulled through a die of smaller diameter, and the tension in the wire as it exits the die is the drawing stress. It must be lower than the strength of the drawn wire, since the wire is pulled by its exit. The drawing stress is the sum of the ideal work of deformation, the friction work and the redundant work of the shear deformation of the metal.

What is the formula used here?

The calculator uses σd = σ̄ ε (1 + μ cot α), where σ̄ is the mean flow stress, ε = ln(A0 / Af) is the true strain, μ the coefficient of friction and α the half-angle of the die. The first factor is the ideal drawing stress without friction. The term μ cot α adds the friction. The redundant work, which depends on the die angle, is not included, and it adds 5% to 15%.

What is the largest possible reduction?

With no friction and a perfectly plastic metal, the drawing stress equals the flow stress when ε = 1, which is a reduction of 63.2% in one pass. With friction and the redundant work, the practical reduction per pass is much lower, usually 15% to 30%, and the wire is drawn through several dies in sequence, with annealing between them if the metal hardens.

What are the limits of this calculator?

It gives the force of an ideal single pass of a round wire at a low speed. It does not include the strain hardening of the metal inside the pass, the heating, the back tension, the speed of drawing, the die geometry with a bearing land or the drawing of tubes. For a drawing line, the tension at each die and the power of the capstans must be computed for the whole sequence.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.