Skip to content
Omnikalc

Wire rope capacity calculator: minimum breaking force and working load limit

Enter the grade, the construction and the diameter of a wire rope, the efficiency of its termination and the design factor to get the minimum breaking force, the usable strength and the working load limit.

Updated on
Your inputs
in

Value out of range

%

Value out of range

Value out of range

Results

Working load limit (WLL)

3,752 lb

Minimum breaking force
23,453 lb
Minimum breaking force
11.73 tons
Usable strength with the termination
18,762 lb
Working load limit (WLL)
1.88 tons

The strength of a wire rope depends on its diameter, its grade, its construction and its end termination. The wire rope capacity calculator estimates the minimum breaking force, the usable strength with the termination and the working load limit for a given design factor.

How the calculation works

  • Select the rope grade (IPS or EIPS, the strength class of the wires) and the construction: 6×19 or 6×36 with an independent wire rope core (IWRC).
  • Enter the nominal diameter of the rope in inches and the efficiency of the end termination: about 80% for a wedge socket or a spliced eye, and close to 100% for a proper swaged fitting.
  • Enter the design factor: 5 is the usual value for general lifting, and 8 to 10 is used for personnel lifting or for severe service.
  • The calculator estimates the breaking force F = K d² Rr from the standard of wire ropes (EN 12385), then applies the termination efficiency and divides by the design factor to get the working load limit.

Example

A 1/2 in (12.7 mm) 6×19 IWRC rope of EIPS grade (1960 MPa) has a minimum breaking force of 0.33 × 12.7² × 1960 / 1000 = 104.3 kN, which is 23,453 lb or 11.7 tons. With a wedge socket at 80%, the usable strength is 18,762 lb. With a design factor of 5, the working load limit is 3,752 lb, or 1.88 tons.

Why it matters

The calculator helps riggers, contractors, farmers and students to check the order of magnitude of a rope for a lift, a winch or a guy line, to compare diameters and grades and to see how much the termination and the design factor reduce the load that can be used. It is a quick check before looking at the catalog.

Good to know

Use the catalog value for the rope that you have. Do not use a rope with broken wires, kinks or corrosion beyond the limit of the standard. Keep the bend radius over sheaves at 20 times the diameter or more. Remember that a sling at an angle carries more tension than the load, and that a shock load can double the force.

The sling angle calculator gives the tension of a sling at an angle, the winch size calculator sizes the machine, the pulley calculator covers the mechanical advantage and the bolt shear capacity calculator checks the pins and shackles.

Frequently asked questions

How is the strength of a wire rope estimated?

The minimum breaking force of a rope is about F = K × d² × Rr, where d is the nominal diameter, Rr is the grade of the wires in MPa and K is a factor that depends on the construction, 0.33 for a 6×19 rope with a steel core and 0.356 for a 6×36. The result is close to the values of the manufacturers’ catalogs. For a real lift, always use the breaking force given by the catalog or the certificate of the rope.

What is the design factor?

The design factor, or safety factor, is the ratio of the minimum breaking force to the working load. A factor of 5 is the usual minimum for general lifting with wire rope slings, and a higher factor is used for lifting people, for loads that can shock, or when the rope is worn or bent over small sheaves. The working load limit is the usable strength divided by the design factor.

Why does the termination reduce the strength?

The fitting that holds the end of the rope is often the weakest part of the assembly. A wedge socket keeps about 80% of the strength of the rope, a hand-spliced eye about 80% to 90%, and a swaged sleeve or a pressed fitting close to 100% when it is made properly. Rope clips keep only about 80%, and only with the right number of clips and the right torque.

What are the limits of this calculator?

It gives a rough estimate, not a rating for a lifting operation. It does not include the loss of strength from bending over a sheave or a pin of small diameter, the angle of a sling, the wear, the broken wires, the corrosion, the shock load or the temperature. Follow the standard and the manufacturer’s data, and have the lift planned by a qualified person.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.