Skip to content
Omnikalc

Pump wire-to-water efficiency calculator: electric power and cost of a pumping system

Enter the flow, head, pump, motor and drive efficiencies, operating hours and electricity price to get the hydraulic power, the electric power drawn, the wire-to-water efficiency, and the annual energy and cost.

Updated on
Your inputs
gpm

Value out of range

ft

Value out of range

Value out of range

%

Value out of range

%

Value out of range

%

Value out of range

h

Value out of range

$/kWh

Value out of range

Results

Wire-to-water efficiency

63.1 %

Good overall efficiency
Hydraulic power delivered to the liquid
12.63 hp
Electric power drawn
14.92 kW
Annual electricity
89,498 kWh/year
Annual electricity cost
10,740 $/year

The pump wire-to-water efficiency calculator gives the hydraulic power, the electric power drawn, the overall efficiency of the pump, the motor and the drive, and the yearly energy and cost of a pumping system.

How the calculation works

  • Enter the flow rate, the total head and the specific gravity of the liquid. The calculator finds the hydraulic power delivered to the liquid.
  • Enter the efficiencies of the pump, of the motor and of the variable frequency drive (100% if there is no drive).
  • The wire-to-water efficiency is the product of the three efficiencies, and the electric power is the hydraulic power divided by it.
  • Enter the operating hours and the electricity price to get the annual energy and the cost.

Example

A pump delivers 500 gpm of water against 100 ft of head, which is 500 × 100 × 1 / 3,960 = 12.63 hp of hydraulic power. The pump is 70% efficient, the motor 93% and the drive 97%, so the wire-to-water efficiency is 0.70 × 0.93 × 0.97 = 63.1%. The electric power drawn is 12.63 × 0.746 / 0.6315 = 14.92 kW. Over 6,000 h this is 89,498 kWh, and at $0.12/kWh the cost is $10,740 per year.

Why it matters

The calculator helps plant engineers, facility managers, water utility staff and energy consultants to find the real operating cost of a pump, to compare a pump, a motor or a drive with a more efficient alternative and to evaluate the payback of an upgrade. It also gives a figure for energy audits.

Good to know

Take the efficiencies at the real operating point, not at the best efficiency point. Use the nameplate or test data of the motor at the actual load. Check whether the pump is oversized, which is the most common cause of a poor efficiency. Use the annual hours at each flow when the load varies.

The pump power calculator gives the power of a pump, the electricity cost calculator converts energy to money, the motor current calculator checks the supply and the horsepower and torque calculator converts the shaft power.

Frequently asked questions

What is the wire-to-water efficiency?

It is the ratio of the hydraulic power given to the liquid to the electric power taken from the supply. It is the product of the efficiencies of every link in the chain: the drive, the motor and the pump. A pump with 70% efficiency, a motor with 93% and a drive with 97% gives a wire-to-water efficiency of 63%. It is the number that sets the real energy cost of pumping.

Why does the total efficiency matter more than the pump efficiency?

Pumping often represents 20 to 25% of the electricity used in industry, and the energy cost over the life of a pump is many times its purchase price. A small gain in each element multiplies: for example, raising the pump efficiency from 65% to 75% saves 13% of the electricity. Looking at the whole chain avoids optimizing one part while the others waste energy.

Does a variable frequency drive always save energy?

The drive itself loses 2 to 4% of the power, so it reduces the efficiency at the design point. It saves energy when the flow varies, because the power falls roughly with the cube of the speed, instead of being wasted by a throttling valve. If the pump runs at full flow most of the time, a drive does not save energy and the 100% value should be entered.

What is not included?

The calculator uses a single pump efficiency, while real pumps have an efficiency that changes with the flow along the curve. It ignores the losses in the cables and the transformer, and it assumes a constant operating point. For a system with variable flow, compute the energy for each operating point, or use hours-at-flow data, and add them.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.