Skip to content
Omnikalc

Two-span continuous beam calculator: reactions, moments and deflection

Enter the uniform load, the length of the two equal spans and the stiffness of the section to get the reactions, the negative and positive moments and the maximum deflection of a continuous beam.

Updated on
Your inputs
kips/ft

Value out of range

ft

Value out of range

ksi

Value out of range

in⁴

Value out of range

Results

Maximum negative moment (over the middle support)

75.0 kip·ft

Reaction at each end support
11.25 kips
Reaction at the middle support
37.50 kips
Maximum positive moment (in each span)
42.19 kip·ft
Maximum deflection
0.258 in
Span divided by the deflection (L / Δ)
931
Within the usual floor limit of L/360

A continuous beam on three supports is statically indeterminate: the reactions and the moments depend on the stiffness. The two-span continuous beam calculator gives the end and middle reactions, the negative and positive moments and the maximum deflection of two equal spans under a uniform load.

How the calculation works

  • Enter the uniform load per unit length on the beam (including its self-weight) and the length of each of the two equal spans.
  • Enter the modulus of elasticity E of the material (29,000 ksi for steel, about 1,600 ksi for wood) and the moment of inertia I of the section.
  • The calculator uses the solution of the beam with three supports: the end reactions 3wL/8, the middle reaction 5wL/4, the negative moment wL²/8 and the positive moment 9wL²/128.
  • It gives the maximum deflection wL⁴ / (185 EI) and the ratio L/Δ, to compare with the limits of L/360 for a floor or L/240 for a roof.

Example

A beam of two spans of 20 ft carries 1.5 kips/ft, with E = 29,000 ksi and I = 300 in⁴. The end reactions are 3 × 1.5 × 20 / 8 = 11.25 kips and the middle reaction is 5 × 1.5 × 20 / 4 = 37.5 kips. The negative moment over the middle support is 1.5 × 20² / 8 = 75.0 kip·ft, and the positive moment is 9 × 1.5 × 20² / 128 = 42.19 kip·ft. The deflection is 0.258 in, a ratio L/Δ of 931, better than L/360.

Why it matters

The calculator helps structural engineering students, designers and builders to size the beams of floors, roofs, decks and bridges that run over a middle support, and to check the moment and the deflection quickly. It also shows the advantage of the continuity over two separate spans.

Good to know

Use the factored load for the strength and the service load for the deflection. Check the top reinforcement or the compression flange over the middle support. If the load can act on one span only, such as a live load, check the alternate loading, which gives a higher positive moment than the full load.

The beam deflection calculator covers the simple spans, the wood beam span calculator sizes lumber beams, the cracking moment calculator checks a concrete section and the moment of inertia calculator gives the stiffness of a section.

Frequently asked questions

What is a continuous beam?

A continuous beam rests on more than two supports, without a hinge over the interior supports. It is statically indeterminate, so the equations of equilibrium are not enough to find the reactions: the stiffness of the beam also counts. For two equal spans and a uniform load, the solution is known, with the middle support carrying 62.5% of the total load of 2wL, or 1.25 wL.

Why is the negative moment the largest?

Over the middle support, the beam bends in the opposite sense (hogging) with a moment of wL²/8, about 1.8 times the maximum positive moment of 9wL²/128 in the spans. This is why the top bars of a concrete beam are placed over the supports, and why a continuous steel or wood beam is checked first at the middle support. The positive moment occurs at 3/8 of the span from the end support.

Why is a continuous beam better than two simple beams?

Two simple spans of length L under the same load have a maximum moment of wL²/8 at the middle of each span and a deflection of 5wL⁴/(384EI), which is 2.6 times that of the continuous beam. The continuous beam is stiffer, uses less material and is more economic, but it is sensitive to the settlement of the supports, which can change the moments.

What are the limits of this calculator?

It applies to a prismatic beam with two equal spans, simple supports at rigid levels and a uniform load on both spans. A load on one span only, unequal spans, a point load or a settlement of the supports change the results. For those cases, use the three-moment equation or a frame program, and check the shear and the lateral buckling of the compression flange.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.