Skip to content
Omnikalc

Well shock chlorination calculator: how much bleach does your well need?

Enter the casing diameter, the water depth, the extra plumbing volume, the target ppm and the bleach strength to get the amount of bleach to add.

Updated on
Your inputs
in

Value out of range

ft

Value out of range

gal

Value out of range

ppm

Value out of range

%

Value out of range

Results

Bleach to add

0.53 gal

Within the usual range for a shock chlorination
Bleach to add in cups
8.4 cups
Water standing in the well
118 gal
Total water volume to disinfect
158 gal
Pure chlorine needed
119.2 g

Disinfecting a well after a repair or a bad test comes down to getting the right dose of chlorine for the volume of water. The well shock chlorination calculator takes the casing diameter, the water depth, the extra volume in the plumbing, the target concentration and the bleach strength, and gives the bleach to add in gallons and cups, the water in the well, the total volume and the pure chlorine needed.

How the calculation works

  • Enter the inside diameter of the well casing and the depth of the water standing in it, that is, from the water level down to the bottom.
  • Add the extra water held in the pipes, the pressure tank and the water heater, since the chlorinated water is run through the whole system.
  • Enter the target concentration in parts per million and the chlorine strength of the bleach printed on the label.
  • The volume of the water column is π × r² × depth. The bleach to add is total volume × target ÷ (strength × 10,000), since 1 percent is 10,000 ppm.

Example

A 6-inch well holds 80 ft of water, which is π × (0.25 ft)² × 80 × 7.48 = 117.5 gallons. With 40 gallons more in the plumbing, the total is 157.5 gallons. To reach 200 ppm with a 6 percent bleach, you need 157.5 × 200 ÷ (6 × 10,000) = 0.525 gallons, which is 8.4 cups. That is about 119 grams of pure chlorine. A 5-inch casing with the same depth would need about 6.5 cups.

Why it matters

Too little chlorine leaves the bacteria alive and gives a false sense of safety, while too much is hard to flush, harms a septic system and corrodes pipes. Working out the right quantity from the real volume avoids both and removes the guessing that comes with rules of thumb.

Good to know

Chlorine bleach is corrosive and gives off harmful fumes. Wear gloves and eye protection, never mix bleach with acids or ammonia, and work in a ventilated area. This calculator does not replace the instructions of your health authority or a licensed well contractor, who can also find the cause of contamination. Dispose of the flushed water as they advise.

The water purification calculator covers other ways to treat water, the rainwater calculator sizes a collection system, the pool chlorine calculator does the same dosing for a pool, and the well drawdown calculator checks the water level in a pumped well.

Frequently asked questions

What is shock chlorination?

It is the one-time addition of a large dose of chlorine to a well and the plumbing to kill bacteria, such as coliforms. It is done after a repair, a flood, a new pump or a positive bacteria test. The strong chlorine solution stays in contact for several hours, then the system is flushed until the chlorine smell is gone.

What concentration should I use?

Health agencies commonly suggest between 50 and 200 ppm of free chlorine, which is 50 to 200 mg/L. The calculator defaults to 200 ppm. A lower dose can fail to disinfect heavily contaminated wells, while a higher one is harder to flush out and can corrode fittings. Follow the guidance of your local health authority.

Which bleach should I use?

Use plain, unscented household bleach with no added cleaners or thickeners. The label shows the strength, often 5 to 8.25 percent sodium hypochlorite in North America. Bleach loses strength with time and heat, so use a fresh bottle, and enter the true strength so that the dose is right.

What happens next?

Pour the bleach in, run each tap until you smell chlorine, and let the system rest for 8 to 24 hours without drinking or using the water. Then flush the system outdoors, away from plants and septic tanks if possible, until the smell is gone, and have the water retested for bacteria after a few days.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.