Skip to content
Omnikalc

Entrance skin dose calculator (radiography)

Enter the tube output per mAs at one meter, the mAs, the focus to skin distance, the backscatter factor and the field size to get the incident air kerma, the entrance skin dose, the dose area product and the comparison with a reference level.

Updated on

Educational tool, not medical advice: this page does not diagnose and does not replace a doctor, nurse or pharmacist. It has not been reviewed by a healthcare professional. Editorial and medical policy

Your inputs
mGy/mAs

Value out of range

mAs

Value out of range

cm

Value out of range

Value out of range

cm

Value out of range

cm

Value out of range

mGy

Value out of range

Results

Entrance skin dose

1.67 mGy

Well below the reference level
Incident air kerma (without backscatter)
1.23 mGy
Dose area product
1.48 Gy·cm²
Share of the reference level
17 %
Rough effective dose from DAP (0.2 mSv per Gy·cm², abdomen)
0.30 mSv

The entrance skin dose calculator gives the incident air kerma, the entrance skin dose and the dose area product of a radiograph from the tube output, the mAs, the distance and the backscatter factor.

How the calculation works

  • Enter the tube output, the mAs and the focus to skin distance.
  • Enter the backscatter factor, the field size and the reference level.
  • Read the ESD, the DAP and the share of the reference level.

Example

A tube with an output of 0.05 mGy/mAs at 1 m used at 20 mAs and a distance of 90 cm gives an incident air kerma of 0.05 × 20 × (100 / 90)² = 1.23 mGy. With a backscatter factor of 1.35 the skin dose is 1.67 mGy. A field of 30 × 40 cm gives a DAP of 1.48 Gy·cm², and the dose is 17 % of a reference level of 10 mGy.

Why it matters

The calculator helps radiographers, medical physicists and quality control teams who check patient doses against diagnostic reference levels, and students who learn the dose quantities of radiography.

Good to know

The estimate assumes that the tube output is known for the kVp and the filtration used, and that the field is fully on the patient. The output varies with the generator, the age of the tube and the added filtration, so measure it regularly. Patient dose depends on thickness: a large patient needs a higher mAs and gets a higher skin dose, but the dose at the receptor stays constant. The DAP is easier to measure in practice with a meter on the collimator and is the basis of most dose audits. The effective dose factor given here is only a rough guide that varies by examination, so use published conversion factors for the body part examined. Follow the ALARA principle and compare your results with local or national reference levels.

The exposure adjustment calculator changes the technique, the CT dose calculator treats scanners, the inverse square law calculator shows the effect of distance and the dose comparison calculator puts a dose in context.

Frequently asked questions

What is the entrance skin dose?

It is the dose to the skin where the beam enters the patient, including the radiation scattered back from the body. It equals the incident air kerma multiplied by the backscatter factor, about 1.3 to 1.4 for typical beams.

How do I get the tube output?

The output is measured with a dosemeter during quality control, in mGy per mAs at a distance of one meter, for each kVp and filtration. It rises roughly with the square of the kVp. A typical value at 80 kVp is 0.04 to 0.06 mGy/mAs.

Is a high skin dose dangerous?

Skin effects such as redness need a dose of several grays, far more than a radiograph gives. They matter in long interventional procedures. The goal in radiography is optimization, not the avoidance of skin injury.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.