Skip to content
Omnikalc

Patellar height (Insall-Salvati and Caton-Deschamps) calculator

Enter the length of the patellar tendon, the length of the patella, the distance from the lower edge of the patellar joint surface to the tibial plateau and the length of the patellar joint surface to get the two ratios and the classification of the patellar height.

Updated on

Educational tool, not medical advice: this page does not diagnose and does not replace a doctor, nurse or pharmacist. It has not been reviewed by a healthcare professional. Editorial and medical policy

Your inputs
mm

Value out of range

mm

Value out of range

mm

Value out of range

mm

Value out of range

Results

Insall-Salvati ratio (tendon / patella)

1.05

A normal patellar height (0.8 to 1.2)
Caton-Deschamps index (distance / joint surface)
1.15
A normal patellar height (0.8 to 1.2)

The patellar height calculator gives the Insall-Salvati ratio and the Caton-Deschamps index from measurements on a lateral knee X-ray, and classifies the patella as normal, alta or baja.

How the calculation works

  • Measure the tendon and the patella on the X-ray.
  • Measure the distance and the joint surface for the Caton-Deschamps index.
  • Read the two ratios and the classification.

Example

A patellar tendon of 44 mm and a patella of 42 mm give an Insall-Salvati ratio of 44 / 42 = 1.05. A distance of 38 mm over a joint surface of 33 mm gives a Caton-Deschamps index of 1.15. Both are in the normal range of 0.8 to 1.2, so the patellar height is normal.

Why it matters

The calculator helps orthopedic and sports medicine residents, radiologists, physiotherapists and students who read a knee X-ray in a patient with patellar instability or anterior knee pain.

Good to know

The radiograph must be taken from the side with the knee bent at about 30 degrees, since the tendon is slack in full extension and the ratio is falsely changed. The Insall-Salvati ratio was published in 1971, and its main limit is the patella with a long inferior pole, which gives a false normal result. The Caton-Deschamps index was described in 1982, and several variants exist, where the distance is measured to different points of the tibia, so reading reports requires attention to the version used. The threshold of 1.2 for patella alta is common to both, and 0.8 or 0.6 are the lower limits that have been proposed. Patella alta is found in a majority of patients with recurrent dislocation of the patella, and patella baja often follows tibial tubercle surgery, knee replacement or a long immobilization. Magnetic resonance imaging can measure the height on the sagittal image, but values differ from the X-ray. The calculator is an aid to learning, and the imaging report decides.

The patellar tracking calculator measures the Q-angle and the tibial tubercle-trochlear groove distance, the range of motion calculator measures the movement of the knee, the Lysholm calculator scores knee function and the leg length calculator checks the limb.

Frequently asked questions

What is patellar height?

It is the position of the kneecap relative to the knee joint on a side view X-ray. A patella that sits too high engages late in the groove of the femur when the knee bends, and is less stable.

How do the two ratios differ?

The Insall-Salvati ratio compares the length of the patellar tendon with the length of the patella. The Caton-Deschamps index compares the distance from the joint surface of the patella to the tibia with the length of that joint surface, and it is less affected by the shape of the lower pole of the patella.

What is done if the patella is high?

Strengthening and bracing for most patients. In recurrent dislocation with a marked patella alta, surgeons may move the tibial tubercle down, a distalization, in addition to other procedures.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.