Skip to content
Omnikalc

Rolled throughput yield calculator: how many units survive every step?

Enter the first-pass yield of up to five process steps to get the rolled throughput yield, the average yield per step and the units to start to reach a good-unit target.

Updated on
Your inputs
%

Value out of range

%

Value out of range

%

Value out of range

%

Value out of range

%

Value out of range

Value out of range

Results

Rolled throughput yield (RTY)

90.01%

Moderate: the steps add up to a noticeable loss
Average yield per step (geometric mean)
97.92%
Units to start to get the good units needed
1,112
Units lost along the way
112
Lowest step yield
96.8%
Defects per million units at the end
99,927

A process of several steps loses a few units at each one, and the losses add up. The rolled throughput yield calculator takes the first-pass yield of five steps and the good units you need, and gives the rolled throughput yield, the average yield per step, the units to start, the units lost, the lowest step yield and the defects per million.

How the calculation works

  • The first-pass yield of a step is the share of units that go through it without scrap or rework. Enter it for each of the five steps.
  • The rolled throughput yield is the product of the step yields: RTY = Y₁ × Y₂ × Y₃ × Y₄ × Y₅. It is the chance that a unit passes every step right the first time.
  • The average yield per step is the fifth root of the RTY. It is always lower than the best step and higher than the worst.
  • To get a number of good units, units to start = good units needed ÷ RTY, rounded up. The units lost are the difference.

Example

Five steps have yields of 98.5 %, 97.2 %, 99.1 %, 96.8 % and 98.0 %. The RTY is the product, 90.01 %, even though each step looks good on its own. The average yield per step is 97.92 %. To make 1,000 good units, the line must start 1,112 units, so 112 are lost. That is about 99,927 defects per million. The weakest step, at 96.8 %, is the best place to work on.

Why it matters

Looking at each step alone hides how much is lost in total. A line of five steps that each pass 97 percent loses more than 14 percent of its units overall. RTY shows that real figure and points to where improvement is worth the most.

Good to know

RTY assumes the steps are independent and the yield of each is measured the first time through, before any rework. If rework is counted as good, the figure is a final yield and not an RTY. The calculator uses five steps. For fewer steps, enter 100 percent for the unused ones.

The DPMO calculator expresses defects per million opportunities and sigma level, the OEE calculator measures how well equipment is used and the process capability calculator compares process spread with specifications.

Frequently asked questions

What is rolled throughput yield?

It is the probability that a unit goes through all the steps of a process without a defect and without rework. It is found by multiplying the first-pass yields of the steps. It is a lean and Six Sigma measure that reveals the hidden loss that individual step yields conceal.

Why is it lower than the final yield?

The final yield only counts the units that pass the last inspection, after rework and scrap have been sorted out along the way. RTY counts only units right the first time, so it includes the cost of rework that never shows up in a final yield.

How does RTY relate to defects per million?

The share of units that do not pass every step right is 1 minus RTY. Multiplying by a million gives the defects per million units, in the sense of units with at least one defect, not defects per opportunity as in DPMO.

How do I improve the RTY?

Look for the step with the lowest yield and find the cause of its defects, because improving the weakest step has the biggest effect. Raising a 96.8 percent step to 99 percent lifts the RTY more than a small gain on a step that already scores 99.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.