Skip to content
Omnikalc

Bond enthalpy calculator: estimate how much heat a reaction releases or absorbs

Choose the bonds broken and formed in a reaction and their numbers to estimate the reaction enthalpy, the energies of the bonds and the energy per unit mass.

Updated on
Your inputs

Value out of range

Value out of range

Value out of range

Value out of range

Value out of range

Value out of range

g

Value out of range

Results

Reaction enthalpy ΔH

-802 kJ/mol

Exothermic: the reaction releases heat
Energy needed to break the bonds
2,648 kJ/mol
Energy released by the new bonds
3,450 kJ/mol
Reaction enthalpy ΔH in kcal
-191.7 kcal/mol
Energy released per unit mass of reactants
21,496 BTU/lb

Chemical reactions release or absorb heat because bonds break and form. The bond enthalpy calculator estimates the reaction enthalpy from the bonds broken and the bonds formed, using average bond enthalpies for 15 common bonds. It gives the energy to break the bonds, the energy released by the new bonds, the ΔH in kJ and kcal per mole, and the energy per unit mass.

How the calculation works

  • Write the reaction and count the bonds broken in the reactants and the bonds formed in the products. Choose up to three types of each, with their numbers.
  • The energy needed to break the bonds is the sum of count × bond enthalpy, and the same for the bonds formed.
  • The reaction enthalpy is ΔH ≈ Σ(bonds broken) − Σ(bonds formed) in kJ/mol.
  • A negative ΔH is exothermic. Enter the mass of the reactants per mole of reaction to see the energy released per unit mass.

Example

For the combustion of methane, CH₄ + 2 O₂ → CO₂ + 2 H₂O, the bonds broken are 4 C–H (1,652 kJ) and 2 O=O (996 kJ), a total of 2,648 kJ. The bonds formed are 2 C=O (1,598 kJ) and 4 O–H (1,852 kJ), a total of 3,450 kJ. So ΔH = −802 kJ/mol (−191.7 kcal/mol). For 16.04 g of methane, this is 50.0 kJ/g, or about 21,500 BTU/lb.

Why it matters

Bond enthalpies give a quick check of whether a reaction is exothermic, and an estimate of the heat of combustion of a fuel without a table of data. They are a standard exercise in general chemistry, and also useful to compare fuels by the energy per unit mass.

Good to know

The method uses average bond enthalpies of gaseous molecules, so the results are estimates and not accurate thermochemical data. It does not take into account the state of the substances (liquids and solids need the enthalpy of vaporization or fusion), resonance, ring strain, or differences between molecules for the same bond type. For precise values, use standard enthalpies of formation.

The heat of combustion calculator uses tabulated values of fuels, the latent heat calculator covers the change of phase that the method ignores, the specific heat calculator covers the temperature rise from the heat, and the equilibrium constant calculator covers how far a reaction goes.

Frequently asked questions

What is the bond enthalpy?

It is the average energy needed to break one mole of a given type of bond in the gas phase, such as 413 kJ/mol for a C–H bond. Breaking bonds takes energy (endothermic), and forming bonds releases it (exothermic). The balance of the two gives the heat of the reaction.

How accurate is the method?

Because the bond enthalpy is an average over many molecules, the result is only an estimate, usually within 5 to 10 % of the true value, and sometimes more. It works best for reactions of gases with similar bonds. For methane combustion, the estimate of −802 kJ/mol is close to the true value of −802 kJ/mol for gaseous water, but this agreement is partly lucky.

Why is the result lower than a heat of combustion table?

The bond energies apply to gases, so the water formed is a gas. A table value for the higher heating value (−890 kJ/mol for methane) includes the condensation of the water to a liquid, which adds 2 × 44 kJ/mol. The method gives the lower heating value.

How should I count the bonds?

Draw the structure of every molecule. Count each bond type in the reactants that is not present in the products as broken, and each bond type in the products that is absent from the reactants as formed. A double bond counts as one bond of its own type. Check that the equation is balanced before counting.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.