Skip to content
Omnikalc

Boost converter calculator: design a step-up DC-DC converter

Enter the input and output voltage, the current, the frequency, the inductor and the capacitor to get the duty cycle, the input current, the inductor ripple, the peak current and the output ripple.

Updated on
Your inputs
V

Value out of range

V

Value out of range

A

Value out of range

kHz

Value out of range

µH

Value out of range

µF

Value out of range

%

Value out of range

Results

Duty cycle

58.33 %

Duty cycle in a normal range
Average input current
2.667 A
Inductor ripple current
0.583 A
Peak inductor current
2.958 A
Inductor ripple ratio ΔI / input current
0.219
Continuous conduction with a moderate ripple
Output voltage ripple
24.82 mV
Power lost in the converter
1.333 W

A boost converter steps a voltage up, as when a battery has to power a 12 V device. The boost converter calculator gives the duty cycle, the input current, the inductor ripple current, the peak current, the output voltage ripple and the losses from the voltages, the output current, the frequency, the inductor, the capacitor and the efficiency.

How the calculation works

  • Enter the input voltage, the output voltage (which must be higher) and the output current.
  • Enter the switching frequency, the inductance, the output capacitance and the efficiency of the converter.
  • In continuous conduction, the duty cycle is D = 1 − Vin / Vout, the input current is Vout Iout / (η Vin) and the inductor ripple is ΔI = Vin D / (L f).
  • The output ripple is estimated as ΔVout = Iout D / (f C), and the peak inductor current is the average plus half the ripple.

Example

A boost converter makes 12 V from 5 V at 1 A, switching at 500 kHz with a 10 µH inductor, a 47 µF capacitor and 90 % efficiency. The duty cycle is 58.33 %, the average input current 2.667 A, the inductor ripple 0.583 A and the peak current 2.958 A. The output ripple is 24.82 mV and the converter dissipates 1.333 W.

Why it matters

Boost converters are in battery-powered devices, LED drivers, power-factor correction and solar chargers. The calculator gives the first numbers needed to pick an inductor, a switch and a capacitor, and it shows when the converter leaves continuous conduction.

Good to know

The formulas are for an ideal converter in continuous conduction, with the efficiency used only for the input current and the losses. They ignore the voltage drops of the switch and the diode, which change the real duty cycle by a few percent, the resistance of the inductor, the ESR of the capacitor and the dead time. The output ripple is the capacitive part only. At a duty cycle above 85 % or a large step-up ratio, the real converter works poorly, and a different topology is better.

The buck converter calculator covers the step-down case, the rectifier ripple calculator gives the ripple of a filter capacitor, the MOSFET power loss calculator estimates the losses of the switch, and the RC filter calculator covers the output filtering.

Frequently asked questions

How does a boost converter work?

A switch (a transistor) connects an inductor to the input for a fraction D of the period, which stores energy in the inductor. When the switch opens, the inductor current flows through a diode to the output and the stored energy is added to that of the source, so the output voltage is higher than the input. In ideal continuous conduction, Vout = Vin / (1 − D).

Why does the input current exceed the output current?

The power is conserved, apart from the losses, so Vin Iin = Vout Iout / η. A converter that raises the voltage must draw a higher current from the source. Raising 5 V to 12 V at 1 A needs about 2.7 A at the input with 90 % efficiency, and this sets the size of the inductor, the switch and the source.

How do I choose the inductor?

A larger inductor reduces the ripple current, ΔI = Vin D / (L f), and keeps the converter in continuous conduction, but it is bigger and has more resistance. A common design makes the ripple 20 to 40 % of the average input current. The inductor must also withstand the peak current without saturating, so its saturation current must be higher than the peak given here.

What is the output ripple and how do I reduce it?

The output capacitor supplies the load current while the switch is closed, so the voltage falls by ΔV = Iout D / (f C). A higher frequency or a larger capacitor lowers it. The equivalent series resistance (ESR) of the capacitor adds another term, often larger than the capacitive one for electrolytic capacitors, which this simple calculation does not include.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.