Skip to content
Omnikalc

Inverting buck-boost converter calculator

Enter the input voltage, the negative output voltage, the load current and the frequency to size an inverting buck-boost converter.

Updated on
Your inputs
V

Value out of range

V

Value out of range

A

Value out of range

kHz

Value out of range

Value out of range

mV

Value out of range

Results

Inductor

31.1 µH

Duty cycle
29.4 %
Average inductor current
1.42 A
Peak inductor and switch current
1.70 A
Voltage across the switch and the diode
17.0 V
Minimum output capacitor
29.4 µF

The inverting buck-boost converter calculator gives the duty cycle, the inductor, the average and peak currents, the voltage on the switch and the minimum output capacitor for a converter that makes a negative rail.

How the calculation works

  • Enter the input voltage, the magnitude of the output voltage and the load current.
  • Enter the switching frequency, the ripple ratio of the inductor current and the allowed output ripple.
  • The calculator finds the duty cycle, the inductance for the ripple you chose, the currents and the capacitor that holds the output ripple.

Example

To make −5 V from 12 V at 1 A and 200 kHz, the converter runs at a duty cycle of 29.4 %. The inductor carries 1.42 A on average and 1.70 A at the peak, and needs 31.1 µH for a ripple of 40 %. The switch and the diode see 17.0 V, and an output ripple of 50 mV needs at least 29.4 µF.

Why it matters

The calculator helps designers of analog and sensor circuits who need a negative bias or a negative supply for an amplifier, an LCD or a gate driver from a single positive battery or rail, and students who learn the three basic switching topologies.

Good to know

The inverting topology has a pulsed input current and a pulsed output current, so it needs a good input capacitor and an output capacitor with a low resistance. The output is negative with respect to the ground of the input, which is simple for a load referenced to ground but needs care for the feedback divider and the controller. Real converters lose a few percent in the diode and the switch, so choose the duty cycle with a margin and check the output at the lowest input voltage and the highest load. Stay in continuous conduction by keeping the inductor larger than the value given here, or use a controller designed for discontinuous mode.

The boost converter and buck converter calculators size the two other basic topologies, the flyback converter calculator gives the isolated version and the MOSFET power loss calculator gives the heat in the switch.

Frequently asked questions

What does an inverting buck-boost do?

It produces an output voltage of opposite polarity to the input, with a magnitude that can be lower or higher than the input. The ideal relation is Vo = −Vin × D / (1 − D). A duty cycle below 50 % lowers the magnitude, above 50 % it raises it. It is a common way to make a negative rail from a positive supply.

Why is the inductor current higher than the load current?

The inductor feeds the load only while the switch is off, which is a fraction 1 − D of the period. To deliver the load current on average it must carry Io / (1 − D) on average, and the switch carries the same current during the on-time. Both the switch and the diode must be rated for the peak current.

How is the output capacitor chosen?

During the on-time the capacitor alone supplies the load, so it loses the charge Io × D / f. The ripple voltage is about ΔV = Io × D / (f × C), which gives the minimum capacitance. The equivalent series resistance of the capacitor adds a second ripple term, so use a low-ESR ceramic or polymer type.

What are the limits of the calculation?

The calculator assumes continuous conduction and ideal parts. It does not account for the diode drop, the switch resistance or the losses of the inductor, which lower the real output a little. The controller needs a floating or level-shifted gate drive because the switch is referenced to the negative output. Check the data sheet of the controller for the topology.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.